Data Link Configuration Status - Test
使用本步骤进行专门说明书诊断代码的故障排除。 如果以下任一诊断代码为现行状态,则使用本步骤。
注: 以下某些代码可能不适用于特定的应用。
Show/hide table
数据链路配置状态故障诊断代码 | |||
---|---|---|---|
J1939 代码 | CDL 代码 | 代码说明
(代码说明可能不同) |
注释 |
639-14 | 247-14 | J1939 网络 #1:专门说明书 | 从 CAN A 数据总线接收到的数据格式错误。
记录该代码。 |
- | 246-14 | 专有 CAN 数据链路:专门说明书 | 从专有 CAN 数据总线接收到的数据格式错误。
记录该代码。 |
- | 296-14 | 变速箱控制专门说明书 | 接收自变速箱控制器的数据格式错误。
记录该代码。 |
- | 588-14 | 监控系统显示器专门说明书 | 从显示器监控器模块上接收到的数据格式错误。
记录该代码。 |
- | 1603-14 | 机器控制模块:专门说明书 | 接收自机器控制模块的数据不兼容。
记录该代码。 |
按所列步骤顺序完成以上步骤。
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 检查有无相关的 -9 代码 A. 建立电子维修工具和发动机电子控制模块 (ECM) 之间的通信。 B. 在执行任何故障排除或清除诊断故障代码前,从发动机 ECM 下载"保固报告"。 C. 检查有无现行诊断代码。 |
相关故障代码 |
结果:记录了相关代码 -9。 修理:修理所有相关的 -9 代码后继续进行此步骤。 参考故障排除, "数据链路 - 测试"。 如果 -14 代码在排除 -9 代码后依然存在,则转至测试步骤 2。 结果:未记录相关代码 -9。 转至测试步骤 2。 |
2. 检查个性化模块代码与应用之间的兼容性 A. 连接电子维修工具。 B. 选择与记录的代码相关的 ECM 连接。 C. 检查个性化模块代码是否对应用有效。 |
兼容的个性化模块 |
结果:此代码对应用有效。 转至测试步骤 3。 结果:此代码对应用无效。 修理:获取正确的闪存文件后更新 ECM。 复位所有现行代码并清除所有记录的代码。 使机组返回工作。 |
3. 检查配置参数 A. 通过检查配置参数确保参数经过正确编程。 参考故障排除, "配置参数"。 B. 选择与记录的代码相关的 ECM 连接。 |
正确的配置参数 |
结果:配置参数经过正确编程设定。 继续测试步骤 4。 结果:配置参数未经过正确编程设定。 修理:编程设定参数,以满足数据链路上其他模块的要求。 复位所有现行代码并清除所有记录的代码。 使机组返回工作。 |
4. 检查与数据链路上所有其他 ECM 之间的兼容性 A. 利用 SIS web TMI 内的发货信息确定数据链路上的所有其他 ECM 或显示器是否兼容。 B. 选择与记录的代码相关的 ECM 连接。 |
兼容的 ECM |
结果:ECM 不兼容。 修理:利用正确的模块更换不兼容的 ECM。 复位所有现行代码并清除所有记录的代码。 使机组返回工作。 如果该步骤无法排除故障,请联系代理商解决方案网络 (DSN)。 |
Caterpillar Information System:
PM820, PM822, and PM825 Cold Planer Rotor Drive Clutch Bearings - Lubricate
120 and 120 AWD Motor Grader Safety Messages
120 and 120 AWD Motor Grader Monitoring System
C32 Marine Engines Electronic Control Module - Remove and Install - Hazardous Location
G3516 TA Engine Test ECM Mode
3512C Generator Set Engine Auxiliary Water Pump - Remove and Install
3412 Generator Set Sensor Signal (Analog, Passive) - Test
G3600 A4 Engines Nitrogen Oxide Sensor - Calibrate
C15 Generator Set Electronic Modular Control Panel 4 (EMCP 4)
120 and 120 AWD Motor Grader Rollover Protective Structure (ROPS) - Inspect
120 and 120 AWD Motor Grader Secondary Steering - Test
120 and 120 AWD Motor Grader Tandem Breather - Clean/Replace
G3606 and G3608 Engines Prelubrication Oil Pump - Remove
794 AC Off-Highway Truck Field Assembly Platform - Assemble
3512C Generator Set Engine Engine Oil Cooler - Remove and Install
794 AC Off-Highway Truck Field Assembly Stairway - Install
G3500H 50Hz Generator Sets Product Installation
G3500H 50Hz Generator Sets General Maintenance Information
G3500H 50Hz Generator Sets Coolant (NGEC) - Change
G3500H 50Hz Generator Sets Generator Set Alignment - Check - Generator Sets
G3500H 50Hz Generator Sets Overhaul (In-Frame)
3412 Generator Set Sensor Supply - Test
3512C Generator Set Engine Engine Oil Cooler - Disassemble
3512C Generator Set Engine Engine Oil Cooler - Assemble