Water Pump - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 207-1600 (1)     | Rubber Lubricant     | 1     |
207-1601 | Rubber Lubricant     | 1     |
Show/hide table
( 1 ) | For Use In EAME |
- Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
- Disconnect tube assembly (1) .
Show/hide table
Illustration 1 | g02175361 |
- Remove bolts (2) and temperature regulator housing (3) .
- Remove tube (4) .
- Disconnect tube assembly (6) .
Show/hide table
Illustration 2 | g01868394 |
- Remove bolts (5) and elbow (7) .
- Loosen clamp (8) .
Show/hide table
Illustration 3 | g01868396 |
- Remove bolts (10), elbow (9), and the hose.
- Remove bolts (12) and water pump (11) .
Show/hide table
Illustration 4 | g01868395 |
- Remove O-ring seal (13) from water pump (11) .
Show/hide table
Illustration 5 | g01868397 |
- Remove seal (16) .
Show/hide table
Illustration 6 | g01868453 |
- Remove bolts (14) and inlet cover (15) .
- Remove O-ring seal (16) from inlet cover (15) .
Show/hide table
Illustration 7 | g01868454 |
Installation Procedure
- Install water pump (11) in the reverse order of removal.
- Apply Tooling (A) to all O-rings and seals in the installation procedure.
- Install clamp (8) and tighten clamp (8) to a torque of 14 ± 1 N·m (124 ± 9 lb in).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C13 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C32 Generator Set General Maintenance Information
2013/06/06 Installing Connecting Rod Bearings in G3600, 3600 and C280 Engines {1225}