Exhaust Gas Valve (NRS) - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 207-1600 (1) | Rubber Lubricant | 1 |
Show/hide table
| ( 1 ) | For Use In EAME |
- Disconnect harness assemblies (1) and disconnect tube assemblies (2) .
Show/hide table
 | |
| Illustration 1 | g02848005 |
- Loosen clamp (4) and remove tube assembly (3). Discard clamp (4) and the O-ring seals.
- Loosen clamps (6) and remove hose (7) .
Show/hide table
 | |
| Illustration 2 | g02848045 |
- Remove bolts (9), clip (8), and exhaust control valve (5) .
Installation Procedure
- Install exhaust control valve (5) in the reverse order of removal.
- Apply Tooling (A) to the O-ring seals and the venturi-side bore of tube assembly (3) .
- Tighten clamps (4) to a torque of 8.5 ± 2 N·m (75 ± 18 lb in).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
C9.3 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2013/06/11 A New Prechamber and Gasket Are Available for Certain G3600 Engines {1106}
2013/06/03 New Fuel Lines Kits Are Used on Certain C9.3 Industrial Engines {1288}
2013/06/06 An Alternate Fuel Line Is Available For Certain C18 Marine Engines {1274}
C15 and C18 Tier 4 Final Engines Clean Emissions Module
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C13 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install