Exhaust Cooler (NRS) - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 207-1600 (1)     | Rubber Lubricant     | 1     |
207-1601 | Rubber Lubricant     | 1     |
Show/hide table
( 1 ) | For Use In EAME |
Start By:
- Remove the exhaust elbow.
- Refer to Operation and Maintenance Manual, "Cooling System Coolant (ELC) - Change" for the correct draining and filling procedures.
- Loosen clamp (1) .
Show/hide table
Illustration 1 | g02846078 |
- Loosen clamp assemblies (2) and remove bellows (3). Discard clamp assemblies (2) and bellows (3) .
- Remove elbow assemblies (4) and (6). Remove the O-ring seals.
- Remove bolts (5) .
- Remove nuts (7). Remove exhaust gas cooler (8) .
Show/hide table
Illustration 2 | g02169114 |
Installation Procedure
- Install exhaust gas cooler (8) in reverse order of removal.
- Apply Tooling (A) to the bores of elbow assemblies (4) and (6), and the O-ring seals.
- Install bellows (3) with the flow arrow pointing towards the exhaust cooler. Total misalignment of the bellows is 1.50 mm (0.060 inch) lateral and 1.50 mm (0.060 inch) axial.
- Tighten clamps (1) and (2) to a torque of 7.5 ± 1 N·m (66 ± 9 lb in).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
C9.3 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2013/06/11 A New Prechamber and Gasket Are Available for Certain G3600 Engines {1106}
2013/06/03 New Fuel Lines Kits Are Used on Certain C9.3 Industrial Engines {1288}
2013/06/06 An Alternate Fuel Line Is Available For Certain C18 Marine Engines {1274}
C15 and C18 Tier 4 Final Engines Clean Emissions Module
Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F} Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F}
Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714} Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714}
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install