Fuel Filter Base - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 185-3630     | Strap Wrench As     | 1     |
B     | −     | Loctite 271     | −     |
- Turn the fuel supply to the OFF position and turn the power disconnect switch to the OFF.
- Cut clips (1) and remove hose assemblies (2) and the fittings.
Note: Depending on the machine application, the fuel filter assembly will be mounted in various places on a machine. The following procedure is a general procedure for servicing the fuel filter base. Refer to the machine-specific engine supplement manual for more specific instructions.
Show/hide table
Illustration 1 | g02845402 |
- Disconnect the harness assembly from fuel temperature sensor (3). Remove temperature sensor (3) .
Show/hide table
Illustration 2 | g02845417 |
- Disconnect the harness assembly from pre-filter fuel pressure sensor (4). Remove pressure sensor (4) .
- Use Tooling (A) to remove fuel filters (5). Remove fuel filter base (6) .
- Remove adapter assembly (7) and studs (8) .
Show/hide table
Illustration 3 | g02845480 |
Installation Procedure
- Install fuel filter base (6) in reverse order of removal.
- Apply Tooling (B) to the threads of studs (8). Tooling (B) should cover the threads of the stud, shown as Distance (C), which is a measurement of 7.6 ± 0.8 mm (0.3 ± 0.03 inch).
Show/hide tableIllustration 4 g02845499
- Tighten studs (8) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
- Tighten fuel temperature sensor (1) to a torque of 20 ± 3 N·m (177 ± 26 lb in).
- Tighten pre-filter fuel pressure sensor (2) to a torque of 10 ± 2 N·m (88 ± 17 lb in).
- Lubricate the fuel filter seals with the fluid that is being sealed prior to installation. Use Tooling (A) to tighten the fuel filters (5) to a torque of 35 ± 3 N·m (26 ± 2 lb ft).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
C9.3 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2013/06/11 A New Prechamber and Gasket Are Available for Certain G3600 Engines {1106}
2013/06/03 New Fuel Lines Kits Are Used on Certain C9.3 Industrial Engines {1288}
2013/06/06 An Alternate Fuel Line Is Available For Certain C18 Marine Engines {1274}
C15 and C18 Tier 4 Final Engines Clean Emissions Module
Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F} Aftertreatment Filter Maintenance on Tier 4 Final Products Equipped with a Diesel Particulate Filter (DPF), Diesel Oxidation Catalyst (DOC) and a Selective Catalyst Reduction (SCR) Filter {108F}
Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714} Installation of a Dual Tapered Roller Bearing HEUI Hydraulic Pump onto Certain C7 ACERT Engines {1714}
C13, C15, and C18 Tier 4 Final Engines Turbocharger
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install