Air Inlet Elbow - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | -     | LOCTITE 592 Thread Sealant     |
-     |
Start By:
- Remove the solenoid valve (exhaust balance).
- Disconnect the harness assembly from temperature sensor (5). Remove temperature sensor (5) .
Show/hide table
Illustration 1 | g02849799 |
- Remove hose assembly (4) and the fittings. Remove clip (3) .
- Loosen the clamps for hose (2) and remove hose (2) .
- Loosen clamp (1) and remove air inlet elbow (6) .
- Disconnect the harness assembly from pressure sensor (7). Remove pressure sensor (7) .
Show/hide table
Illustration 2 | g02849824 |
- Remove O-ring seal (8) and remove air inlet manifold (9). Remove and discard the gasket from air inlet manifold (9) .
- Remove bolts (11) and remove tube (10) and the O-ring seal.
Show/hide table
Illustration 3 | g02849857 |
- Remove pin spring (12) and dowel (14) .
Show/hide table
Illustration 4 | g02849867 |
- Remove tube (14) and the wave ring.
- Remove plug (15) .
Show/hide table
Illustration 5 | g02849879 |
Installation Procedure
- Install air inlet elbow (6) in the reverse order of removal.
- Apply Tooling (A) to plug (15) .
- Install pin spring (12) to the depth illustrated by Dimension (B). Dimension (B) is 6.0 ± 0.50 mm (0.20 ± 0.020 inch).
Show/hide tableIllustration 6 g02849917
- Install dowel (14) to the depth illustrated by Dimension (C). Dimension (C) is 2.9 mm (0.11 inch).
- Tighten pressure sensor (7) to a torque of 10 ± 2 N·m (89 ± 18 lb in).
- Tighten temperature sensor (5) to a torque of 20 ± 3 N·m (177 ± 27 lb in).
- Tighten clamp (1) to a torque of 8.5 ± 2 N·m (75 ± 18 lb in).
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Cooler (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Fuel Transfer Pump - Remove and Install
Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822} Instructions for Determining Failed Active Power Module (APM) Inverter on Certain Uninterruptible Power Supplies{1418, 4822}
2013/07/22 New Exhaust Manifold Groups Are Available for Certain 3512C Petroleum Engines {1059}
C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052} C175 HAA Air System Lifting Device{0599, 0629, 0632, 1052, 1052}
C9.3 Engines for Caterpillar Built Machines Inlet Module (Catalyst) - Remove and Install
2013/06/11 A New Prechamber and Gasket Are Available for Certain G3600 Engines {1106}
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Pan - Remove and Install
C13 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install