Engine Oil Pan - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 4C-9614     | Silicone Sealant     | 1     |
- Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change" for the proper draining and filling procedures.
- Remove bolts (3), stud bolts (2), and the fasteners.
Show/hide table
Illustration 1 | g02859716 |
- Remove clips (4) and (5). Position the harness assembly out of the way.
- Remove engine oil pan (1). Remove and discard the isolation seal.
- Remove bolts (7) and (8). Remove suction bell assembly (6) .
Show/hide table
Illustration 2 | g02859778 |
- Remove switch assembly (9) .
Show/hide table
Illustration 3 | g02859838 |
- Remove plugs (10) and (11) .
Installation Procedure
- Install engine oil pan (1) in the reverse order of removal.
- Apply Tooling (A) at four locations marked (A). Tooling (A) should be applied in 4 ± 1 mm (0.16 ± 0.04 inch) diameter beads.
Note: All joints using Tooling (A) must be assembled within 10 minutes of the application.
Show/hide tableIllustration 4 g02466177
Note: Ensure that the oil pan and mating surfaces are clean and free of oil.
- Tighten plugs (11) to a torque of 90 ± 15 N·m (66 ± 11 lb ft).
- Tighten plugs (10) to a torque of 70 ± 15 N·m (52 ± 11 lb ft).
- Tighten bolts (3) and stud bolts (2) in the above sequence.
Show/hide tableIllustration 5 g02466597
Torque Sequence
- Apply Tooling (A) at four locations marked (A). Tooling (A) should be applied in 4 ± 1 mm (0.16 ± 0.04 inch) diameter beads.
Caterpillar Information System:
C13 Engine for Caterpillar Built Machines Camshaft Gear - Remove and Install
C13 Engine for Caterpillar Built Machines Front Cover - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Flywheel - Remove and Install
C13 Engine for Caterpillar Built Machines Water Temperature Regulator Housing - Remove and Install
C13 Engine for Caterpillar Built Machines Water Pump - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Air Inlet Elbow - Remove and Install
C13 Engine for Caterpillar Built Machines Combustion Head - Remove and Install
C13 Engine for Caterpillar Built Machines Ignition Coil - Remove and Install
C13 Engine for Caterpillar Built Machines Exhaust Gas Valve (NRS) - Remove and Install
C13 Engine for Caterpillar Built Machines Turbocharger - Remove and Install
C13 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (ARD Combustion Air) - Remove and Install
C13 Engine for Caterpillar Built Machines Pressure Sensor (Cooled Exhaust Gas) - Remove and Install
C13 Engine for Caterpillar Built Machines Inlet Air Temperature Sensor - Remove and Install
C32 Generator Set General Maintenance Information
2013/06/06 Installing Connecting Rod Bearings in G3600, 3600 and C280 Engines {1225}
Well Service Pumps General Hazard Information
Well Service Pumps Fire Prevention and Explosion Prevention
Well Stimulation Pumps Crushing Prevention and Cutting Prevention
C27 and C32 Generator Sets Product Installation
Well Stimulation Pumps Before Operation
Well Service Pumps Operation