Air Shutoff - Remove and Install
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
Show/hide table
如果不遵循正确的程序或不使用推荐的工具,可能会对人员造成伤亡。 为避免对人员造成伤亡,应使用推荐的工具遵循已经制定好的程序。 |
Show/hide table
在拆下进气切断装置前,拉动进气切断装置上的跳开关旋钮或按下紧急停止按钮,以释放叶片锁闩。 如果在拆下进气切断装置后释放叶片锁闩,可能导致严重的人身伤害。 |
- 手动释放空气切断阀。 通过拉或压释放空气切断阀上的旋钮。 确保空气切断阀上的指示器径直向下指向"关闭"位置。 如果空气切断阀不触发,请参阅故障诊断与排除, "空气切断阀系统"。
Show/hide table
图 1 g01303618 - 将管组件 (1) 从空气切断阀 (4) 上断开。
- 通过将螺栓 (2) 从空气切断阀 (4) 的接头 (3) 上松开断开进气软管 (5)。
- 拆下将空气切断阀 (4) 安装到进气歧管上的螺栓 (6) 和垫圈。
- 拆下空气切断阀 (4) 后拆下密封垫。
注: 检查进气管中有无碎屑。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 将新密封垫和空气切断阀 (4) 安装到进气歧管上。 安装螺栓 (6) 和垫圈,并将螺栓 (6) 上紧到
25 ± 6 N·m (18 ± 4 lb ft) 的扭矩。 - 重新连接进气软管 (5)。 将螺栓 (2) 安装到接头 (3) 上,并将螺栓 (2) 上紧到
25 ± 6 N·m (18 ± 4 lb ft) 的扭矩。 - 将管组件 (1) 重新连接到空气切断阀 (4) 上。
- 复位空气切断阀上的指示器。 确保指示器上的箭头径直向上指向"打开"位置。
- 测试空气切断阀 (4) 是否正常工作,并参阅操作和保养手册, "空气切断阀"。
Show/hide table
图 2 | g01303618 |
Caterpillar Information System:
C15 On-Highway Engine Vibration Damper and Pulley
G3520C and G3520E Generator Set Engines Oil Pressure Is High
Caterpillar Parts Pricing{1000, 7000, 756P} Caterpillar Parts Pricing{1000, 7000, 756P}
Reuse and Salvage for 3200 Engine Cylinder Blocks {1201} Reuse and Salvage for 3200 Engine Cylinder Blocks {1201}
G3520C and G3520E Generator Set Engines Sensor Signal (PWM) - Test
2006/09/11 Make Sure That the Plug and the Gasket are Installed in the Cylinder Head {1100, 1118}
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission Does Not Respond to Shift Selector
C13 On-highway Engine Main Bearing Journal
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Replaced Relay or Solenoid Does Not Operate
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Engine Does Not Crank
C13 On-highway Engine Crankshaft
CX28, CX31 and CX35 On-Highway Transmissions Power Train Electronic Control System Transmission Does Not Automatically Shift Back Into Gear
G3520C and G3520E Generator Set Engines Sensor Signal (Analog, Passive) - Test
G3520C and G3520E Generator Set Engines Generator Output Power - Test
G3520C and G3520E Generator Set Engines Sensor Signal (Analog, Active) - Test
C11 and C13 Engines and 14M and 16M Motor Graders Speed Control (Switch) - Test
3512B Marine Auxiliary Engine Speed Sensor - Clean/Inspect
3512B Marine Auxiliary Engine Starting Motor - Inspect
C15 and C18 Engines for Caterpillar Built Machines Speed/Timing - Test
C13 On-highway Engine Electric Starting Motor
Adapting the Jacobs Brake Module Function{1119, 1129} Adapting the Jacobs Brake Module Function{1119, 1129}
C11 and C13 Engines and 14M and 16M Motor Graders Starting Aid - Test
C15 On-Highway Engine Engine Oil Pan
G3520C and G3520E Generator Set Engines Sensor Supply - Test