Cylinder Block
Show/hide table
图 1 | g02529482 |
Show/hide table
223-9252 缸体总成的技术规格 | |||
项目 | 数量 | 零件 | 技术规格说明 |
1 | 1 | 227-1204 垫片 | 在装配过程中,垫板 (2) 的底部、缸体的顶部和垫片 (1) 的两个表面上绝不能有燃油、机油、水、粘合剂、组装固定胶或其他任何污染物。
垫片的厚度为 |
A | 1 | 4N-1650 定位销 | 安装前,将绿色 Loctite 609 涂覆到定位销上。
定位销伸出缸体顶面的长度为 |
2 | 1 | 6I-4421 垫板 | 垫板的最大厚度为 |
B | 1 | 1S-9540 定位销 | 定位销伸出缸体顶面的长度为 |
C | 1 | 6I-1055 定位销 | 安装前,将绿色 Loctite 609 涂覆到定位销上。
定位销伸出缸体顶面的长度为 |
E | 2 | 4N-0683 定位销 | 定位销伸出缸体端部的长度为 |
F | 2 | 266-6038 定位销 | 定位销伸出缸体端部的长度为 |
3 | - | - | 使用油液润滑即将密封的 O 形密封圈孔。 |
H | - | - | 塞的安装深度为 |
Show/hide table
图 2 | g02725676 |
Show/hide table
项目 | 数量 | 零件 | 技术规格说明 |
4 | 1 | 197-9322 缸套 | 用清洁的发动机机油彻底润滑缸套的整个内径。 |
5 | - | - | 使用油液润滑即将密封的 O 形密封圈孔。 |
J | - | - | 从曲轴轴承孔中心线到新缸体顶部的尺寸为 制动器应用的最小尺寸应为 非制动器应用的最小尺寸应为 |
K | - | - | 缸体中用于安装主轴承的孔径为 |
L | - | - | 主轴承盖的宽度为 缸体上用于安装主轴承盖的宽度为 |
M | - | - | 从曲轴轴承孔中心线到缸体油底壳油轨底部的尺寸为 |
6 | 14 | 3P-1323 轴承盖螺栓 | 按照以下步骤拧紧主轴承盖螺栓:
1. 将清洁的发动机机油涂抹在螺栓的螺纹上。 2. 将凸舌端的螺栓拧紧至扭矩为 3. 将凸舌端对面一端的螺栓拧紧至扭矩为 4. 将凸舌端对面一端的螺栓再拧紧 120 ± 5 度。 4. 将凸舌端的螺栓再拧紧 120 ± 5 度。 对每个螺栓重复此步骤。 |
缸体顶部接触面的总体平整度必须在 |
Caterpillar Information System:
C3.3 and C4.4 Generator Sets Camshaft - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Piston and Rings - C32 Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Install
C3.3 and C4.4 Generator Sets Cylinder Head - Install - Four Cylinder Engines
C3.3 and C4.4 Generator Sets Cylinder Head - Remove - Four Cylinder Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Remove
C3.3 and C4.4 Generator Sets Crankshaft Pulley - Remove and Install
C3.3 and C4.4 Generator Sets Flywheel - Install
C3.3 and C4.4 Generator Sets Flywheel - Remove
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E194 High Exhaust Temperature
C3.3 and C4.4 Generator Sets Water Temperature Regulator - Remove and Install
C15 Industrial Engine Engine Pressure Sensor Open or Short Circuit - Test
2006/10/23 An Improved Turbocharger is Used {1052, 1053}
C9 Industrial Engines Piston and Rings
C3.3 and C4.4 Generator Sets Engine Oil Pan - Remove and Install
C15 Industrial Engine Low Power/Poor or No Response to Throttle
C15 Industrial Engine Poor Acceleration or Response
C4.4 Industrial Engine Engine Oil and Filter - Change
C4.4 (Mech) Industrial Engine Crankshaft Seals
C4.4 Industrial Engine Alternator
C4.4 Industrial Engine Starter Motor
C3.3 and C4.4 Generator Sets Engine Oil Filter Base - Remove and Install
C3.3 and C4.4 Generator Sets Speed/Timing Sensor - Remove and Install
C3.3 and C4.4 Generator Sets Electric Starting Motor - Remove and Install