Poor Acceleration or Response
故障的根本原因按次序列于下面:
- 诊断代码
- 冷起动模式
- 客户指定参数(正常工作)
- 传动系数据链路
- 扭矩限制开关
按次序进行下述诊断步骤:
- 某些诊断代码可能会造成性能不良。 这些诊断代码的目的是保护发动机。
- 将 Caterpillar 电子技师(ET)连接到数据链路接口接头。
- 检查有无激活的代码或记录的代码。 继续进行此步骤之前,对存在的任何代码进行故障诊断与排除。
- 确保发动机未处在冷起动模式。
- 起动发动机。
- 在 Cat ET上监视状态屏幕。
- 检查所有状态屏幕顶部是否有 "Cold Mode"(冷起动模式)标记。
注: 直到 "Cold Mode"(冷起动模式)标记变为不激活状态,发动机才会接受到满功率。
- 确认故障与不正确设定的用户指定参数无关。
- 进入 Cat ET 上的 "Configuration"(配置)屏幕。
- 检查下列参数:
- "额定编号"
- "发动机转速上限"
- "车速限制"
- "低档位发动机转速限制"
- "中间挡位发动机转速限制"
- "减档保护发动机转速限制"
注: 如果 "Rating Number"(额定编号)编程设定为 0,则发动机限制为 119 kW (160 hp)。
- "额定编号"
- 依次设定各个参数到最大值,确定是否排除该故障。
- 检查"传动系数据链路"。 确保传动系数据链路没有限制功率。
- 在车辆出现故障时监视 "Powertrain Data Link"(传动系数据链路)状态屏幕。
如果 "Powertrain Data Link"(传动系数据链路)状态屏幕显示 "Powertrain Data Link"(传动系数据链路)限制着功率或转速,确认这不是正常的工作状态。 如果不是正常工作状态,请送修车辆 OEM。
- 在车辆出现故障时监视 "Powertrain Data Link"(传动系数据链路)状态屏幕。
- 检查扭矩限制开关。
- 检查 "Torque Limit"(扭矩限制)参数的设定值。
如果 "Torque Limit"(扭矩限制)编程设定为低于 3400 N·m (2500 lb ft),检查状态屏幕上的扭矩限制开关。 确保状态屏幕显示扭矩限制开关 OFF(断开)。 如果扭矩限制开关 ON(接通),且扭矩限制已编程设定,说明系统正常工作。 如果连在此信号输入的开关没有改变接通和断开状态的话,请参阅故障诊断与排除, "PTO 开关电路 - 测试"。
- 检查 "Torque Limit"(扭矩限制)参数的设定值。
Caterpillar Information System:
C15 Industrial Engine Low Power/Poor or No Response to Throttle
C3.3 and C4.4 Generator Sets Engine Oil Pan - Remove and Install
C9 Industrial Engines Piston and Rings
2006/10/23 An Improved Turbocharger is Used {1052, 1053}
C15 Petroleum Generator Set Engines Cylinder Block
C3.3 and C4.4 Generator Sets Camshaft - Remove and Install
C27 and C32 Engines for Caterpillar Built Machines Piston and Rings - C32 Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Install
C3.3 and C4.4 Generator Sets Cylinder Head - Install - Four Cylinder Engines
C3.3 and C4.4 Generator Sets Cylinder Head - Remove - Four Cylinder Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Remove
C3.3 and C4.4 Generator Sets Crankshaft Pulley - Remove and Install
C4.4 Industrial Engine Engine Oil and Filter - Change
C4.4 (Mech) Industrial Engine Crankshaft Seals
C4.4 Industrial Engine Alternator
C4.4 Industrial Engine Starter Motor
C3.3 and C4.4 Generator Sets Engine Oil Filter Base - Remove and Install
C3.3 and C4.4 Generator Sets Speed/Timing Sensor - Remove and Install
C3.3 and C4.4 Generator Sets Electric Starting Motor - Remove and Install
C7 Urban Transit Bus Engines Maintenance Interval Schedule
C4.4 Industrial Engine Gear Group (Front)
C3.3 and C4.4 Generator Sets Engine Enclosure Group - Remove and Install
C4.4 Industrial Engine Exhaust Manifold
C9 Industrial Engines Front Housing and Covers