Camshaft - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-9352 | Engine Stand | 1 |
Start By:
- Remove the engine. Refer to Disassembly and Assembly, "Engine - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Attach the engine to Tooling (A).
- Remove the rocker shaft assembly and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove".
- Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
- Turn the engine upside-down so the valve lifters are held in a position away from the camshaft.
Show/hide table
Illustration 1 g01255264 Show/hide tableNOTICE Do not damage the lobes or the bearings when the camshaft is removed or installed.
- Carefully remove camshaft (1) from the cylinder block.
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1U-9352 | Engine Stand | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Carefully install camshaft (1) in the cylinder block.
- Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
- Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install".
- Remove the engine from Tooling (A).
Note: Ensure that the camshaft is clean. Lubricate the camshaft with clean engine oil prior to installation.
Show/hide table
NOTICE |
---|
Do not damage the lobes or the bearings when the camshaft is removed or installed. |
Show/hide table
Illustration 2 | g01255264 |
End By:
- Install the engine. Refer to Disassembly and Assembly, "Engine - Install".
Caterpillar Information System:
C27 and C32 Engines for Caterpillar Built Machines Piston and Rings - C32 Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Install
C3.3 and C4.4 Generator Sets Cylinder Head - Install - Four Cylinder Engines
C3.3 and C4.4 Generator Sets Cylinder Head - Remove - Four Cylinder Engines
G3508, G3512 and G3516 Engines Engine Oil Cooler - Remove
C3.3 and C4.4 Generator Sets Crankshaft Pulley - Remove and Install
C3.3 and C4.4 Generator Sets Flywheel - Install
C3.3 and C4.4 Generator Sets Flywheel - Remove
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E194 High Exhaust Temperature
C3.3 and C4.4 Generator Sets Water Temperature Regulator - Remove and Install
C15 Industrial Engine Engine Pressure Sensor Open or Short Circuit - Test
C3.3 and C4.4 Generator Sets Water Pump - Remove and Install
C15 Petroleum Generator Set Engines Cylinder Block
2006/10/23 An Improved Turbocharger is Used {1052, 1053}
C9 Industrial Engines Piston and Rings
C3.3 and C4.4 Generator Sets Engine Oil Pan - Remove and Install
C15 Industrial Engine Low Power/Poor or No Response to Throttle
C15 Industrial Engine Poor Acceleration or Response
C4.4 Industrial Engine Engine Oil and Filter - Change
C4.4 (Mech) Industrial Engine Crankshaft Seals
C4.4 Industrial Engine Alternator
C4.4 Industrial Engine Starter Motor
C3.3 and C4.4 Generator Sets Engine Oil Filter Base - Remove and Install
C3.3 and C4.4 Generator Sets Speed/Timing Sensor - Remove and Install