Cylinder Head - Inspect
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Part Name     | Qty     |
8S-6691     | Cylinder Head Stand Set     | 1     |
Show/hide table
Illustration 1 | g00819713 |
Bolt tightening sequence |
- Remove the bolts in the cylinder head in the reverse sequence that is shown in Illustration 1.
Remove the cylinder head from the engine.
- Clean the cylinder head thoroughly. Make sure that the contact surface of the cylinder head and the contact surface of the cylinder block are clean, smooth and flat.
- Inspect the bottom surface of the cylinder head for the following items: pitting, corrosion and cracks. Inspect the area around the valve seat inserts and the holes for the fuel injection nozzles.
- Put the cylinder head (1) on the 8S-6691 Cylinder Head Stand Set (2) .
Show/hide table
Illustration 2 | g00842292 |
Typical example |
- Measure the cylinder head (1) for flatness. Measure the flatness with a straight edge (3) and with a feeler gauge (4) .
- Measure the cylinder block from point (A) to point (B) .
- Measure the cylinder block from point (C) to point (D) .
- Measure the cylinder block from point (A) to point (C) .
- Measure the cylinder block from point (B) to point (D) .
- Measure the cylinder block from point (A) to point (D) .
- Measure the cylinder block from point (B) to point (C) .
Refer to Specifications, "Cylinder Head" for the requirements of flatness.
- Measure the cylinder block from point (A) to point (B) .
Show/hide table
Illustration 3 | g00841853 |
Typical example |
Caterpillar Information System:
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Brake Control Valve (Service)
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Install - Engine in Chassis
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Engine Speed/Timing Sensor - Calibrate
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble - CP-433E and CS-433E
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Remove - Engine in Chassis
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Disassemble
2002/10/07 Cable Assembly for Stabilizer Pads Prevents Unwanted Flipping {7222}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Muffler - Remove and Install
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders 5 Volt Engine Pressure Sensor Supply Circuit - Test
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Pump (Axle Propel and Drum Propel) - Install
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 167-1351 Generator through 167-1354 Generator
740 EJECTOR Articulated Truck Ejector, Steering, Suspension, and Fan Drive Systems Steering System
2002/09/09 The Thrust Bearing in the Final Drive has Changed {4050}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Refrigerant Compressor - Remove and Install - Engine in Chassis
2001/11/19 A New Crankshaft Front Seal Is Now In Production {1160}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Assemble
TL4 Series Soil Finisher Walk-Around Inspection
2001/12/17 Addition to Operation and Maintenance , "Final Drive Preload - Check" {1000, 7000, 7500, 7519}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic System Pressure - Release
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Torque Converter, Transmission and Output Transfer Gears - Install
2001/11/19 The Timing Marks Have Been Improved On The Engine Front and Rear Balancer Gears {1220}
TL4 Series Soil Finisher Bearings - Lubricate
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Water Temperature Regulator - Remove and Install - Engine in Chassis
773E Off-Highway Truck/Tractor and 775E Quarry Truck Ether Starting Aid Cylinder - Replace - If Equipped