Piston Pump (Axle Propel and Drum Propel) - Install
安装步骤
- 将适当的起吊设备连接到活塞泵 (11) 上。 安装活塞泵 (11) 和螺栓 (17) 。 活塞泵的重量约为 84 kg (185 lb)。
Show/hide table
 | |
| 图 1 | g00840744 |
Show/hide table
 | |
| 图 2 | g00840745 |
- 将软管组件 (16) 连接到活塞泵 (11) 。
Show/hide table
 | |
| 图 3 | g00840743 |
- 将软管组件 (15) 连接到活塞泵 (11) 。
Show/hide table
 | |
| 图 4 | g00840742 |
- 将软管组件 (14) 连接到轮轴推进马达 (13) 上。
Show/hide table
 | |
| 图 5 | g00840741 |
- 将软管组件 (12) 连接到活塞泵 (11) 。
Show/hide table
 | |
| 图 6 | g00840740 |
- 安装支架 (3) 和 (10) 并安装螺栓 (5) 。
Show/hide table
 | |
| 图 7 | g00840739 |
- 安装销 (4) 和开口销。
- 连接线束组件 (8) 、电缆扎带 (9) 和卡箍 (7) 。
- 连接线束组件 (6) 。
- 连接软管组件 (1) 和卡箍 (2) 。
End By: 安装活塞泵（振动）。 请参阅 拆解和组装, "活塞泵（振动）- 安装"。
Caterpillar Information System:
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 167-1351 Generator through 167-1354 Generator
740 EJECTOR Articulated Truck Ejector, Steering, Suspension, and Fan Drive Systems Steering System
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
773E Off-Highway Truck/Tractor and 775E Quarry Truck Plate Locations and Film Locations
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Air Cleaner - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Air Inlet Heater - Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
CP-433E, CS-423E and CS433E Vibratory Soil Compactors Vibratory System Piston Motor (Vibratory System)
CP-433E, CS-433E and CS433E Vibratory Soil Compactors Propel System Piston Pump Neutral - Test and Adjust
CP-433E, CS-433E and CS433E Vibratory Soil Compactors Propel System Relief Valve (Charge) - Test and Adjust
2002/02/18 Improved Hydraulic Cylinders with New Seals and Fittings are Used for Harvester Heads {5104, 5554, 5558, 5559, 5572, 5573}
773E Off-Highway Truck/Tractor and 775E Quarry Truck Air Dryer - Check
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders 5 Volt Engine Pressure Sensor Supply Circuit - Test
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Muffler - Remove and Install
2002/10/07 Cable Assembly for Stabilizer Pads Prevents Unwanted Flipping {7222}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Disassemble
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Remove - Engine in Chassis
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble - CP-433E and CS-433E
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Engine Speed/Timing Sensor - Calibrate
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Install - Engine in Chassis
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Brake Control Valve (Service)
3024C and C1.1 Engines for Caterpillar Built Machines Cylinder Head - Inspect
2002/09/09 The Thrust Bearing in the Final Drive has Changed {4050}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Refrigerant Compressor - Remove and Install - Engine in Chassis