Turbocharger - Install - Engine in Chassis
Installation Procedure
Note: Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install the turbocharger and the gasket.
- Install four mounting nuts (8) on turbocharger (1) .
Show/hide table
Illustration 1 | g00841829 |
- Connect tube assembly (4). Tighten four clamps (5) .
Show/hide table
Illustration 2 | g00841814 |
- Connect tube assemblies (6) and (7) .
- Connect tube assembly (3) to turbocharger (1). Tighten four clamps (2) .
Show/hide table
Illustration 3 | g00841811 |
- Close the engine hood.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Engine Speed/Timing Sensor - Calibrate
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble - CP-433E and CS-433E
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Remove - Engine in Chassis
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Disassemble
2002/10/07 Cable Assembly for Stabilizer Pads Prevents Unwanted Flipping {7222}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Muffler - Remove and Install
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders 5 Volt Engine Pressure Sensor Supply Circuit - Test
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Pump (Axle Propel and Drum Propel) - Install
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 167-1351 Generator through 167-1354 Generator
740 EJECTOR Articulated Truck Ejector, Steering, Suspension, and Fan Drive Systems Steering System
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
773E Off-Highway Truck/Tractor and 775E Quarry Truck Plate Locations and Film Locations
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Brake Control Valve (Service)
3024C and C1.1 Engines for Caterpillar Built Machines Cylinder Head - Inspect
2002/09/09 The Thrust Bearing in the Final Drive has Changed {4050}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Refrigerant Compressor - Remove and Install - Engine in Chassis
2001/11/19 A New Crankshaft Front Seal Is Now In Production {1160}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Assemble
TL4 Series Soil Finisher Walk-Around Inspection
2001/12/17 Addition to Operation and Maintenance , "Final Drive Preload - Check" {1000, 7000, 7500, 7519}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic System Pressure - Release
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Torque Converter, Transmission and Output Transfer Gears - Install
2001/11/19 The Timing Marks Have Been Improved On The Engine Front and Rear Balancer Gears {1220}
TL4 Series Soil Finisher Bearings - Lubricate