Brake Control Valve (Service)
Show/hide table
 | |
| Illustration 1 | g02671779 |
Show/hide table
| Specification for 215-3687 Brake Control Valve Gp (SERVICE) | |||
| Item | Qty | Part | Specification Description |
| 1 | 1 | 215-3687 Brake Control Valve Gp | Service brake pressure is 8625 ± 350 kPa (1250 ± 50 psi). |
| The output pressure of the upper port will be approximately 207 kPa (30 psi) higher than the output pressure of the lower port. |
|||
| A | - | - | Installed height for the brake control valve group is 29.7 mm (1.17 inch). |
| B | - | - | Height of the brake control valve group with the service brake in the FULLY APPLIED position is 20.6 mm (0.81 inch). |
| 2 | - | - | Return ports to the hydraulic oil tank. |
| 3 | - | - | Supply ports from the brake accumulator charging valve. |
| 4 | - | - | Supply ports to the service brakes. |
Caterpillar Information System:
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Install - Engine in Chassis
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Engine Speed/Timing Sensor - Calibrate
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble - CP-433E and CS-433E
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Remove - Engine in Chassis
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Disassemble
2002/10/07 Cable Assembly for Stabilizer Pads Prevents Unwanted Flipping {7222}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Muffler - Remove and Install
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders 5 Volt Engine Pressure Sensor Supply Circuit - Test
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Pump (Axle Propel and Drum Propel) - Install
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 167-1351 Generator through 167-1354 Generator
740 EJECTOR Articulated Truck Ejector, Steering, Suspension, and Fan Drive Systems Steering System
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
3024C and C1.1 Engines for Caterpillar Built Machines Cylinder Head - Inspect
2002/09/09 The Thrust Bearing in the Final Drive has Changed {4050}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Refrigerant Compressor - Remove and Install - Engine in Chassis
2001/11/19 A New Crankshaft Front Seal Is Now In Production {1160}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Assemble
TL4 Series Soil Finisher Walk-Around Inspection
2001/12/17 Addition to Operation and Maintenance , "Final Drive Preload - Check" {1000, 7000, 7500, 7519}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic System Pressure - Release
950G Series II and 962G Series II Wheel Loaders and IT62G Series II Integrated Toolcarrier Power Train Torque Converter, Transmission and Output Transfer Gears - Install
2001/11/19 The Timing Marks Have Been Improved On The Engine Front and Rear Balancer Gears {1220}
TL4 Series Soil Finisher Bearings - Lubricate
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Water Temperature Regulator - Remove and Install - Engine in Chassis