Turbocharger - Remove - Engine in Chassis
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
- Open the engine hood.
- Loosen four clamps (2). Disconnect tube assembly (3) from turbocharger (1) .
Show/hide table
 | |
| Illustration 1 | g00841811 |
- Disconnect tube assemblies (6) and (7) .
Show/hide table
 | |
| Illustration 2 | g00841814 |
- Loosen four clamps (5) and disconnect tube assembly (4) .
- Remove four mounting nuts (8) from turbocharger (1) .
Show/hide table
 | |
| Illustration 3 | g00841829 |
- Remove the turbocharger and the gasket.
Caterpillar Information System:
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Disassemble
2002/10/07 Cable Assembly for Stabilizer Pads Prevents Unwanted Flipping {7222}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Muffler - Remove and Install
3126B Engines for the IT62G Series II Integrated Toolcarrier and for the 950G Series II and 962G Series II Wheel Loaders 5 Volt Engine Pressure Sensor Supply Circuit - Test
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Piston Pump (Axle Propel and Drum Propel) - Install
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for 167-1351 Generator through 167-1354 Generator
740 EJECTOR Articulated Truck Ejector, Steering, Suspension, and Fan Drive Systems Steering System
3408E and 3412E Engines for Caterpillar Built Machines Cylinder Liner Projection - Inspect
773E Off-Highway Truck/Tractor and 775E Quarry Truck Plate Locations and Film Locations
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Air Cleaner - Remove and Install
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Air Inlet Heater - Install
3408E and 3412E Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
CP-433E, CS-423E and CS-433E Vibratory Compactors Machine Systems Gear Pump (Steering) - Disassemble - CP-433E and CS-433E
3176C and 3406E Engines for D7R Series II and D8R Series II Track-Type Tractors Engine Speed/Timing Sensor - Calibrate
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Turbocharger - Install - Engine in Chassis
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Braking System Brake Control Valve (Service)
3024C and C1.1 Engines for Caterpillar Built Machines Cylinder Head - Inspect
2002/09/09 The Thrust Bearing in the Final Drive has Changed {4050}
950G Series II Wheel Loader, 962G Series II Wheel Loader and IT62G Series II Integrated Toolcarrier Engine Supplement Refrigerant Compressor - Remove and Install - Engine in Chassis
2001/11/19 A New Crankshaft Front Seal Is Now In Production {1160}
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Travel Motor - Assemble
TL4 Series Soil Finisher Walk-Around Inspection
2001/12/17 Addition to Operation and Maintenance , "Final Drive Preload - Check" {1000, 7000, 7500, 7519}
416D, 420D, 424D, 428D, 430D, 432D, 438D and 442D Backhoe Loaders Hydraulic and Steering System Hydraulic System Pressure - Release