Auxiliary Water Pump - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 1P-0510 | Driver Gp | 1 |
C | 207-1601 | Rubber Lubricant | 1 |
D | 325–5756 | Seal Tool | 1 |
- Do not lubricate the sealing lip of seal (10). Install ring assembly (11). Use Tooling (B) to install seal (10).
Show/hide table
Illustration 2 g01207696 - Install shaft (7) with thrust washer (9) into water pump (3). Install bolts (8).
Show/hide table
Illustration 3 g06095541 - Turn over water pump (3). Use water or Tooling (C) to aid assembly. Use a press and Tooling (D) to install a new seal assembly (12) over shaft (7) and into housing (3). Ensure that the outer shell of the seal is fully seated in the housing.
Show/hide table
Illustration 4 g01207798 Show/hide tableImproper assembly of parts that are spring loaded can cause bodily injury.
To prevent possible injury, follow the established assembly procedure and wear protective equipment.
- Lubricate shaft (7) with clean engine oil. Use Tooling (B) and a suitable press to install impeller (5) onto shaft (7). Install impeller (5) until impeller (5) is flush to ±
0.15 mm (0.006 inch) with shaft (7).Show/hide tableIllustration 5 g01204935 Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
- Install O-ring seal (4) onto cover (2).
Show/hide table
Illustration 6 g01204934 - Install cover (2) onto water pump (3). Install nuts (1).
Show/hide table
Illustration 1 | g01207698 |
End By:
- Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
Caterpillar Information System:
C175-16 and C175-20 Locomotive Engines Engine Oil Pan - Install
C175-16 and C175-20 Locomotive Engines Auxiliary Water Pump - Disassemble
Connecting Rod Bolt Replacement Procedure On Certain C13 Industrial Engines {1218, 1225} Connecting Rod Bolt Replacement Procedure On Certain C13 Industrial Engines {1218, 1225}
C175-16 and C175-20 Locomotive Engines Water Pump - Assemble
New Regulator Service Kits Are Now Available for Certain G3300, G3500, and 3500 Dynamic Gas Blending Engines {1270} New Regulator Service Kits Are Now Available for Certain G3300, G3500, and 3500 Dynamic Gas Blending Engines {1270}
C175-16 and C175-20 Locomotive Engines Water Pump - Disassemble
C175-16 Locomotive Engine Engine Operation
C175-16 Marine Propulsion Engines Fuel System Verification - Test
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Coolant Temperature Is High
C175-16 and C175-20 Locomotive Engines Flywheel Housing - Install
C175-16 and C175-20 Locomotive Engines Engine Oil Pan - Remove
C175-20 Locomotive Engine Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
TR35 Locomotive Transmission Transmission Oil Pump - Disassemble
TR35 Locomotive Transmission Transmission Oil Pump - Assemble
C175-16 and C175-20 Locomotive Engines Fuel Transfer Pump - Remove
A New Cylinder Liner Insert Is Now Used On Certain 3500 Engines {1201, 1217} A New Cylinder Liner Insert Is Now Used On Certain 3500 Engines {1201, 1217}
C175-16 and C175-20 Locomotive Engines Fuel and Auxiliary Water Pump Drive - Remove and Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Cylinder Is Noisy
C175-16 and C175-20 Locomotive Engines Fuel Transfer Pump - Install
SPF343 and SPF343C Trailer Mounted Pumpers Model View Illustrations
C175-16 and C175-20 Locomotive Engines Fuel Control Valve - Remove and Install
PM820, PM822, and PM825 Cold Planer Machine Systems Conveyor Pulley (Head, First Stage) - Remove and Install
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Camshaft
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Crankshaft