Engine Oil Pan - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 1U-7498 | Support Stand As | 4 |
1U-7501 | Extension Tube | 4 | |
B | 421-5661 | Lifting Eye Assembly | 4 |
C | 323-1146 | Engine Lifting Device | 1 |
- Turn the battery disconnect switch to the OFF position.
- Turn the fuel supply valve to the OFF position.
Show/hide table
NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.
Dispose of all fluids according to local regulations and mandates.
- Drain the oil from the engine into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Engine Oil and Filter - Change".
Show/hide table
Illustration 1 g06095073 - Remove bolts (1), bolts (3), and elbow (2).
Show/hide table
Illustration 2 g06095259 - Attach Tooling (C) onto the engine. The weight of the C175-16 engine is approximately
12750 kg (28110 lb) . The weight of the C175-20 engine is approximately14000 kg (30865 lb) .Show/hide tableIllustration 3 g06095267 - Remove bolts (4) and bolts (5).
Show/hide table
Illustration 4 g06095290 - Raise the engine from engine oil pan (6).
Show/hide table
Illustration 5 g06095354 - Position the engine on Tooling (A).
Show/hide table
Illustration 6 g06095472 - Attach Tooling (B) and a suitable lifting device onto engine oil pan (6). The weight of engine oil pan (6) on a C175-16 engine is approximately
591 kg (1303 lb) . The weight of engine oil pan (6) on a C175-20 engine is approximately696 kg (1534 lb) . Remove engine oil pan (6).
Caterpillar Information System:
C175-20 Locomotive Engine Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
C175-16 Locomotive Engine Emergency Stopping
C175-20 Locomotive Engine Before Starting Engine
C175-20 Locomotive Engine Plate Locations and Film Locations
G3500B Engines Fuel System Operation
323F SA and 323F LN Excavator Diesel Exhaust Fluid Filter - Replace
New Software Is Now Available for Cat® Product Link {7606, 7610, 7620} New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Coolant Level Is Low
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Alternator Problem - Charging Problem and/or Noisy Operation
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Acceleration Is Poor or Throttle Response Is Poor
C175-16 and C175-20 Locomotive Engines Engine Oil Filter Housing - Install
C13 Engines for Caterpillar Built Machines Coolant Level Is Low
C175-16 and C175-20 Locomotive Engines Flywheel Housing - Install
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Coolant Temperature Is High
C175-16 Marine Propulsion Engines Fuel System Verification - Test
C175-16 Locomotive Engine Engine Operation
C175-16 and C175-20 Locomotive Engines Water Pump - Disassemble
New Regulator Service Kits Are Now Available for Certain G3300, G3500, and 3500 Dynamic Gas Blending Engines {1270} New Regulator Service Kits Are Now Available for Certain G3300, G3500, and 3500 Dynamic Gas Blending Engines {1270}
C175-16 and C175-20 Locomotive Engines Water Pump - Assemble
Connecting Rod Bolt Replacement Procedure On Certain C13 Industrial Engines {1218, 1225} Connecting Rod Bolt Replacement Procedure On Certain C13 Industrial Engines {1218, 1225}
C175-16 and C175-20 Locomotive Engines Auxiliary Water Pump - Disassemble
C175-16 and C175-20 Locomotive Engines Engine Oil Pan - Install
C175-16 and C175-20 Locomotive Engines Auxiliary Water Pump - Assemble
TR35 Locomotive Transmission Transmission Oil Pump - Disassemble