Start By:
- Remove the high-pressure fuel rail.
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 339-9352 | Cap Kit(1) | 1 |
| 265-2256 | Lint Free Wipes | 1 | |
| (1) | Discard cap after single use. |
| NOTICE |
|---|
|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
 |
|
Do not open the high pressure fuel system without allowing the fuel system to purge. After the engine has shut down, allow the fuel system to purge for ten minutes. This operating fuel system contains high pressure. Exposure to high pressure fuel can result in personal injury. |
Note: Use Tooling (A) to cap tube assemblies, fittings, ports, and any opening in the fuel system to prevent contamination.
Note: Do not remove all the quills at one time. To maintain alignment, leave least two quills attached to the fuel rail at all times. If necessary, replace with new quill.
- Remove bolt (3) and the washer. Remove tube assembly (1). Disconnect harness assembly (2).
Show/hide table
Illustration 2 g02087089 - Apply clean engine oil to Area (X). Repeat for the opposite collar. Remove bolts (4) and (6). Remove tube assembly (5).
Note: Replace bolts (4) and (6) with new bolts.
Show/hide table
Illustration 3 g02087090 - Remove flow limiter (7) from the fuel rail.
Note: Apply protective caps to flow limiter (7 ) to prevent contamination. Clean Tooling (A) before using to avoid contamination in the fuel system.
| |
| Illustration 1 | g02087086 |
Note: Carefully remove Tooling (A) to prevent contamination.
- Apply clean engine oil to the sealing face of flow limiter (7) and the fuel rail.
- Install flow limiter (7) into the fuel rail.
Show/hide table
Illustration 5 g02087089 Show/hide table
Illustration 6 g01285695 - Apply clean engine oil to Area (X). Repeat for the opposite collar. Apply clean engine oil to the ends of tube assembly (5). Replace external O-ring seals on tube assembly (5) and lubricate the O-ring seals on the tube assembly with clean engine oil. Install tube assembly (5).
- Replace bolts (4) and (6) with new bolts and install hand tight. Tighten bolts (4) evenly to a torque of
20 N·m (177 lb in) . - Tighten bolts (6) evenly to a torque of
20 N·m (15 lb ft) . - Tighten bolts (4) evenly to a final torque of
40 ± 5 N·m (30 ± 4 lb ft) . - Tighten bolts (6) evenly to a final torque of
40 ± 5 N·m (30 ± 4 lb ft) .
Show/hide table
Illustration 7 g02087086 - Replace bolts (4) and (6) with new bolts and install hand tight. Tighten bolts (4) evenly to a torque of
- Connect harness assembly (2). Replace the O-ring seals on both ends of tube assembly (1). Install tube assembly (1). Install the washer and bolt (3).
| |
| Illustration 4 | g02087090 |
Note: Use a clean plastic squirt bottle to apply clean engine oil. Do not apply clean engine oil by hand.
End By:
- Install the high-pressure fuel rail.