Flywheel Housing
Show/hide table
 | |
| 图 1 | g03348816 |
发动机后视图 | |
Show/hide table
 | |
| 图 2 | g03348817 |
拧紧顺序 | |
Show/hide table
| 355-5019 飞轮壳总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 在安装飞轮壳之前，检查飞轮壳的前端面和后壳体的后端面。 部件必须没有以下物质：机油、燃油、水、组装固定胶和任何其他污染物。 | |||
| 组装好的曲轴油封总成的安装深度可以在曲轴位于任何轴向位置的时候进行检查。 | |||
| 使用以下步骤拧紧飞轮壳螺栓。 按照图 2 中所示的数字顺序拧紧螺栓。 | |||
| 1 | 2 | 245-3803 螺栓 | 将螺栓 (1) 至螺栓 (2) 拧紧至 55 ± 10 N·m (41 ± 7 lb ft)。 |
| 2 | 8 | 2H-6488 螺栓 | 将螺栓 (3) 至螺栓 (10) 拧紧至 135 ± 20 N·m (100 ± 15 lb ft)。 |
| 3 | 16 | 0L-1143 螺栓 | 将螺栓 (11) 至螺栓 (26) 拧紧至 47 ± 9 N·m (35 ± 7 lb ft)。 |
| 4 | 1 | 142-5868 曲轴油封 | 密封冲头不能在 177.80 ± 0.25 mm (7.000 ± 0.010 in) 的直径内接触密封。 |
| 如果密封件和衬套已经分开了，则不得使用 曲轴油封总成 的密封件和衬套。 | |||
| A | - | - | 套筒与密封件之间的距离为 6.15 至 6.55 mm (0.242 至 0.258 in)。 |
| C | - | - | 自曲轴后端面的套筒安装深度为 1.5 ± 0.5 mm (0.06 ± 0.02 in)。 |
Caterpillar Information System:
C175-16 Locomotive Engine Flywheel Housing - Remove and Install
C175-16 Locomotive Engine High Pressure Fuel Rails - Remove and Install
C175-16 Locomotive Engine Idler Gears (Front) - Remove and Install
C175-16 Locomotive Engine Fuel Transfer Pump - Remove and Install
C175-16 Locomotive Engine Gear Group (Rear) - Remove and Install
C175-16 Locomotive Engine Piston Cooling Jets - Remove and Install
XQP1100 Generator Set Fuel and the Effect from Cold Weather
C175-16 Locomotive Engine Connecting Rod Bearings - Remove and Install
C175-16 Locomotive Engine Crankshaft Main Bearings - Remove and Install
C175-16 Locomotive Engine Fuel Priming Pump - Remove and Install
C7.1-XQ200 Rental Generator Set Refill Capacities
C280-16 Engine Engine Power Ratings
C7.1 Industrial Engine Refill Capacities
C32 Marine Engines Water Manifold - Exhaust
C32 Marine Engines Water Pump
C32 Marine Engines Turbocharger
C32 Marine Engines Water Lines
C175-16 Locomotive Engine Flow Limiter - Remove and Install
C175-16 Locomotive Engine Flywheel - Remove and Install
C175-16 Locomotive Engine Fuel Control Valve - Remove and Install - Primary
3516C Petroleum Well Service Engine Maintenance Interval Schedule
C13, C15, and C18 Tier 4 Final Engines Magnetic Pickup
C32 Marine Engines Water Lines
C175-16 Locomotive Engine Temperature Sensor