Determining Diagnostic Trouble Codes
使用 Cat® 电子技师 (Cat ET) 维修工具确定诊断代码
将 Cat® 电子技师 (Cat ET) 维修工具连接到机器上。 将钥匙起动开关转到运行位置。 启动 Cat ET。 启动 Cat ET 后,将会建立与机器上的电子控制模块的通信。 Cat ET 将会列出电子控制模块。 选择所需的电子控制模块。 利用 Cat ET 确定诊断代码后,请参阅相应诊断代码的测试步骤。
参考故障诊断与排除, "维修工具"
现行诊断代码
Show/hide table
图 1 | g02625416 |
现行诊断代码的典型 Cat® 电子技师 (Cat ET) 维修工具屏幕 |
下述步骤可能会导致记录新的诊断代码。 因此,执行任何步骤之前,先列出所有现行诊断代码,以确定系统有无故障。 在完成各个步骤时,清除因执行该步骤产生的诊断代码。
注: 执行步骤之前,一定要先检查所有断路器。 修复任何断路器跳闸的原因。
Cat ET 中提供了显示现行诊断代码的屏幕。 该屏幕显示所有现行诊断代码。 现行诊断信息包括部件识别符 (CID)、故障模式识别符 (FMI) 和故障的文字描述。
记录的诊断代码
Show/hide table
图 2 | g02625437 |
记录诊断代码的典型 Cat ET 屏幕 |
Cat ET 中提供了显示记录的诊断代码的屏幕。 该屏幕显示所有记录的诊断代码。 Cat ET 会记录间歇性诊断代码。 记录的诊断数据包括部件识别符(CID)、故障模式识别符(FMI)和故障的文字描述。 此外,记录的诊断数据还包括故障出现的次数和两个时间标记。 时间标记显示了第一次发生故障的时间和最后一次发生故障的时间。
诊断信息记录在固定存储器中。 通电时,ECM 会清除过去机器运转 150 小时内未检测到的或未激活的所有诊断代码。
Caterpillar Information System:
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Flash Program
C32 Marine Engines Engine Oil Pressure - Test
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Cooling Fan Control - Test
C32 Marine Engines Fuel System Pressure - Test
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Connector Contact Description
C280 Marine and Petroleum Engines Prelubrication Pump Problem
C13-XQ350 Rental Generator Set Product Lifting
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Oil Level Is Low
C18 Marine Auxiliary and Marine Generator Set Engines Engine Misfires, Runs Rough or Is Unstable
Health Interface Module Configuration and Operation Guide for Certain Trucks Equipped with a Non-Cat Tire Monitoring System {7605} Health Interface Module Configuration and Operation Guide for Certain Trucks Equipped with a Non-Cat Tire Monitoring System {7605}
C18 Marine Auxiliary and Marine Generator Set Engines Engine Has Mechanical Noise (Knock)
C13-XQ350 Rental Generator Set Plate Locations and Film Locations
C32 Marine Engines Vibration Damper - Check
2012/08/23 Kits Are Available for Repair of Exhaust Components on Certain 3516 Electric Power Engines with Center-Mounted Exhaust Systems {1052, 1053, 1059, 1061, 1071}
2012/12/11 New Software is Used on C175-16 Generator Set Engines {1901, 1920}
C280-16 Petroleum Engine Crankshaft Seals
C27 and C32 Engines for Caterpillar Built Machines Exhaust Gas Valve (NRS)
C27 and C32 Engines for Caterpillar Built Machines Electronic Unit Injector Mechanism
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Electrical Connector - Inspect
C18 Generator set and C18 Marine Engines Engine Oil Pump - Remove
3516B Engine Alternator - Remove and Install
C18 Marine Auxiliary and Marine Generator Set Engines Engine Overspeeds
3516B Engine Electronic Control Module (Engine) - Remove and Install
C3.3B and C3.8 Engines for Caterpillar Built Machines Engine Monitoring System