Piston Motor (Hydraulic Fan) - Install
安装步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件说明 | 数量 |
| A | FT-2674 | 真空舱 | 1 |
注: 清洁度是一项重要的因素。 组装之前，应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上，从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏，则应使用新零件进行更换。
- 使用适当的起吊设备定位风扇马达 (9) 。 风扇马达 (9) 的重量约为 25 kg (55 lb)。 安装螺栓 (11) 。 安装接头 (10) 。
Show/hide table
 | |
| 图 1 | g01213351 |
- 连接软管组件 (7) 和 (8) 。
Show/hide table
 | |
| 图 2 | g01650294 |
- 安装管 (6) 。 安装支承 (5) 。
Show/hide table
 | |
| 图 3 | g01213348 |
- 使用适当的起吊设备安装发动机罩 (3) 。 发动机罩 (3) 的重量约为 68 kg (150 lb)。 安装螺栓 (4) 。
Show/hide table
 | |
| 图 4 | g01213346 |
- 关闭检修门 (2) ，然后安装螺栓 (1) 。
Show/hide table
 | |
| 图 5 | g01213345 |
- 关闭左前方检修门。
- 拆下工具 (A) 。
Show/hide table
 | |
| 图 6 | g01213343 |
Caterpillar Information System:
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Piston Motor (Hydraulic Fan) - Remove
C175-16 and C175-20 Engines for Off-Highway Trucks Exhaust Manifold
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Grease Lines
C175-16 Locomotive Engine Exhaust Fitting
G3500B Engines Engine Sensors
G3500B Engines Electronic Control System Parameters
390F MHPU Mobile Hydraulic Power Unit Alternate Exit
G3500B Engines Electronic Control Module (ECM)
Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562} Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562}
TH48-E70 Petroleum Transmission Transmission Warm-up
G3500B Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547} Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547}
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear)
3512B Engine Product Lifting
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Operator Console - Remove and Install
3512B Engine Engine Crankcase Breather - Clean
2008/12/08 A New Cat Compression Brake Is Available. {1119, 1129}
3000 Frame SR5 Electric Power Generation Exciter - Remove and Install
3000 Frame SR5 Electric Power Generation Bearing - Remove and Install - Rear Bearing - Remove and Install
3000 Frame SR5 Electric Power Generation Bus Bar - Remove and Install
3000 Frame SR5 Electric Power Generation Rotor - Remove and Install
G3500B Engines Engine Monitoring System
Procedure to Restore the Residual Magnetic Field on Brushless Alternators{1405} Procedure to Restore the Residual Magnetic Field on Brushless Alternators{1405}
3512B Engine Air Shutoff - Test