Transmission Warm-up
本 TH48-E70 石油变速箱具有在寒冷环境中利用变矩器失速预热变速箱和发动机的功能。
变矩器失速会增加发动机负载,并使变矩器产生热量。 加热后的变矩器油通过变速箱油冷却器将热量传递给发动机冷却液。 待机油返回变速箱后,还将热量传递给油池中的机油。
对于使用 J1939 换档器的应用,可能需要切换至 "2R" 以启用此功能。 对于使用开关接地型换档器的应用,通过切换至停车档并使变速箱的失速启用电路接地来启用此功能。 将 ECM 插脚 J1-64(用户接头插脚 4)接地,接通变速箱的失速启用电路。 符合下列所有条件时,变速箱 ECM 将启用失速。
- 变速箱油温低于
87° C (190° F) 。 - 变矩器油温低于
110° C (230° F) 。 - 发动机转速低于 1000 rpm 并大于 500 rpm 时。
在发生以下某种情况时,变速箱将自动从失速切换到停车档:
- 如果变速箱油温超过
93° C (200° F) 。 - 变矩器油温超过
120° C (248° F) 。 - 发动机转速高于 1300 rpm。
如果在变速箱停车期间发动机转速超过 1000 rpm,将记录"变速箱误操作警告事件"。 选择失速模式时,变速箱将按照上述标准自动在失速和停车档之间循环。 循环到失速的最大速率将由定时器限定到每 60 秒一次。 当变速箱机油冷却或速度下降时,用于变速箱预热的变矩器失速模式将在符合标准时自动接合。
下列激活的电气故障将禁用失速,迫使变速箱挂入停车档。
- 活动 ECPC 电磁阀诊断故障
- 活动锁定离合器电磁阀对蓄电池诊断故障短路
- 变矩器油温传感器故障
- 发动机转速传感器故障
如果在失速模式中变速箱输出速度超过 50 rpm,变速箱将执行下列操作:
- 换至停车档
- 在 Cat 电子技师中记录 718-14 变速箱系统专门说明书诊断代码。
- 亮起淡黄色警告灯并在 J1939 DM2(诊断信息 2)上广播淡黄色警告灯状态。
Caterpillar Information System:
G3500B Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547} Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547}
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Cab - Install
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Cab - Remove
2008/09/29 Serial Number Plate {1000, 7557}
3512B Engine Configuration Parameters
Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
2008/10/01 Diagnostic Code Occurring on C11 and C13 On-Highway Engines {1901, 1920}
G3600 Engines Welding Precaution
3412, 3412C, and 3412E Generator Set Engines Speed Control (PWM) - Test
Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N} Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N}
Procedure for Powering the Battery Charger Continuously{751B} Procedure for Powering the Battery Charger Continuously{751B}
Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562} Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562}
G3500B Engines Electronic Control Module (ECM)
390F MHPU Mobile Hydraulic Power Unit Alternate Exit
G3500B Engines Electronic Control System Parameters
G3500B Engines Engine Sensors
C175-16 Locomotive Engine Exhaust Fitting
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Grease Lines
C175-16 and C175-20 Engines for Off-Highway Trucks Exhaust Manifold
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Piston Motor (Hydraulic Fan) - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Piston Motor (Hydraulic Fan) - Install
3408E and 3412E Engines for Caterpillar Built Machines Gear Group (Rear)
3512B Engine Product Lifting