Welding Precaution
为避免损坏发动机的电子控制模块 (ECM)、集成式感应模块 (ISM)、空气/燃油压力模块、传感器和相关部件,必须采用正确的焊接步骤。 也应考虑用于从动设备的部件。 按照下述步骤在发动机上进行焊接。
- 将发动机控制置于"停机"模式。
- 确保关断通往发动机的燃料供应。
- 从蓄电池上断开负极接线端。
- 从导线线束上断开所有电气部件。 这包括以下组件:
- 从动设备的电气部件
- 发动机电子控制模块 ECM、ISM 和空气/燃油压力模块
- 传感器
- 燃料计量阀
- 阻风门和排气旁通阀(废气旁通阀)执行器
Show/hide table注意 切勿将电气零部件(ECM电子控制模块或电子控制模块传感器) 或电子零部件的接地点用作焊接机的接地点。
- 如有可能,将焊机接地夹直接连接到将要焊接的发动机部件上。 将夹子尽可能地靠近焊接点,以减少焊接电流损坏发动机轴承、电气部件及其他部件的可能性。
- 防止焊接碎屑和/或焊接飞溅物损坏导线线束。
- 采用标准焊接步骤将物料焊接在一起。
Caterpillar Information System:
3412, 3412C, and 3412E Generator Set Engines Speed Control (PWM) - Test
Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N} Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N}
Procedure for Powering the Battery Charger Continuously{751B} Procedure for Powering the Battery Charger Continuously{751B}
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Position Sensor - Calibrate
3512B Generator Set Engine Configuration Parameters
3412, 3412C, and 3412E Generator Set Engines Speed Control - Test
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Pump (Type 2)
3512B Generator Set Engine Event Codes
G3500J Engines Configuration Parameters
3500B Engines Auxiliary Water Pump - Disassemble - Auxiliary Pump (Type 2)
TH48-E70 Petroleum Transmission Safety Messages
An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050} An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050}
2008/10/01 Diagnostic Code Occurring on C11 and C13 On-Highway Engines {1901, 1920}
Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
3512B Engine Configuration Parameters
2008/09/29 Serial Number Plate {1000, 7557}
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Cab - Remove
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Cab - Install
Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547} Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547}
G3500B Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
TH48-E70 Petroleum Transmission Transmission Warm-up
Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562} Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562}
G3500B Engines Electronic Control Module (ECM)
390F MHPU Mobile Hydraulic Power Unit Alternate Exit