Cab - Remove
拆卸步骤
Show/hide table
| 所需工具 | |||
|---|---|---|---|
| 工具 | 零件号 | 零件说明 | 数量 |
| A | 138-7575 | 连杆支架 | 4 |
开始:
- 拆下储物箱。 请参阅拆解和组装, "储物箱和盖（驾驶室） - 拆卸"。
- 拆下护罩 (2) 和地板垫 (1) 。
Show/hide table
 | |
| 图 1 | g01208263 |
- 拆下盖 (3) 和导管 (4) 。
Show/hide table
 | |
| 图 2 | g01208264 |
- 拆下盖 (5) 。
Show/hide table
 | |
| 图 3 | g01208273 |
- 拆下螺栓 (6) 。
Show/hide table
 | |
| 图 4 | g01208274 |
- 断开线束组件 (8) 。 拆下导管 (7) 。
Show/hide table
 | |
| 图 5 | g01208275 |
- 断开线束组件 (9) 和 (10) 。
Show/hide table
 | |
| 图 6 | g01648558 |
- 断开软管组件 (11) 、 (12) 、 (13) 、 (14) 和 (15) 。
Show/hide table
 | |
| 图 7 | g01648460 |
- 断开电缆组件 (16) 和 (17) 。 断开接地母线 (18) 。
Show/hide table
 | |
| 图 8 | g01648462 |
- 断开线束组件 (19) 。
- 断开线束组件 (21) 。
Show/hide table
 | |
| 图 9 | g01648464 |
- 拆卸计算机 (20) 。
- 断开软管 (22) 。
Show/hide table
 | |
| 图 10 | g01650133 |
- 将工具 (A) 和适当的起吊设备连接到驾驶室 (23) 。 驾驶室 (23) 的重量约为 408 kg (900 lb)。 拆下 10 个螺栓 (25) 和 2 个螺栓 (24) 。 拆下驾驶室 (23) 。
Show/hide table
 | |
| 图 11 | g01650134 |
Show/hide table
 | |
| 图 12 | g01650135 |
Caterpillar Information System:
2008/09/29 Serial Number Plate {1000, 7557}
3512B Engine Configuration Parameters
Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
2008/10/01 Diagnostic Code Occurring on C11 and C13 On-Highway Engines {1901, 1920}
G3600 Engines Welding Precaution
3412, 3412C, and 3412E Generator Set Engines Speed Control (PWM) - Test
Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N} Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N}
Procedure for Powering the Battery Charger Continuously{751B} Procedure for Powering the Battery Charger Continuously{751B}
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Position Sensor - Calibrate
3512B Generator Set Engine Configuration Parameters
3412, 3412C, and 3412E Generator Set Engines Speed Control - Test
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Pump (Type 2)
345D, 349D and 349D2 Excavators and 345D MHPU and 349D MHPU Mobile Hydraulic Power Units Machine Systems Cab - Install
Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547} Installation Procedure for Mounting Hydraulic Thumbs with Tool Bars{6547}
G3500B Engines Air/Fuel Ratio Control - NO<SUB>X</SUB> Feedback
TH48-E70 Petroleum Transmission Transmission Warm-up
Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562} Machining the O-ring Groove into the Face of Oversized Bolted Head Hydraulic Cylinders {0677, 5100, 7562}
G3500B Engines Electronic Control Module (ECM)
390F MHPU Mobile Hydraulic Power Unit Alternate Exit
G3500B Engines Electronic Control System Parameters
G3500B Engines Engine Sensors
C175-16 Locomotive Engine Exhaust Fitting
330D, 336D, 336D2, 340D and 340D2 Excavators Machine System Specifications Grease Lines
C175-16 and C175-20 Engines for Off-Highway Trucks Exhaust Manifold