Configuration Parameters
系统配置参数用来指定发动机排放级别、额定功率和具体应用。 这些参数的默认值已在工厂进行了编程。 一些参数可能有所变动,以使配备的发动机符合具体应用。 如果没有使用 Cat 电子技师(ET)中的"复制配置"工具更换电子控制模块(ECM),则必须重新编程系统配置参数。 如果更新了 ECM 闪存文件,千万不要重新编程系统配置参数。 某些配置参数压印在发动机信息标牌上。
注: 有关配置参数的更多详细信息,参考故障诊断与排除手册 , M0065674。
Advisor 监视器显示屏的设定配置参数
可以用 advisor 监视器显示屏更改 Cat 燃气发动机的配置参数。 通过从 advisor 主菜单上选择 "Configuration Menu(配置菜单)",用户可以更改某些配置参数。
该功能受密码保护。 密码默认值设定为 "0"。 可以通过选择 advisor 主菜单上的 "Display Setup(显示设置)"选项随时更改安全密码。 然后,选择 "Change Password/PIN(更改密码/PIN)"选项。 还可以用 Cat ET 更改安全密码。
输入配置模式后,软件监控按键。 用定时器检查 advisor 的"屏幕保护密码"是否已过期。 如果没有在"屏幕保护密码"指定的时间间隔内按下键,advisor 定时器超时。 然后,用户会回到主菜单。 通过选择"屏幕保护密码"选项,将时间间隔配置在 15 到 999 分钟之间。
一些参数受安全密码的保护。 Cat ET 需要用户密码或工厂密码进行更改这些参数。 请参阅故障诊断与排除, "客户密码"和故障诊断与排除, "工厂密码",以了解详情。
注: 出厂密码仅供来自授权的 Cat 代理商的维修技师使用。 Caterpillar 的客户无权访问 Cat 出厂密码系统 (FPS)。 如果受工厂密码保护的参数未经 Caterpillar 的授权擅自更改,则修理可能不包括在 Cat 保修范围内。
有关更多信息,请参阅系统操作/测试和调整, "电子控制系统参数"。
Caterpillar Information System:
3500B Engines Auxiliary Water Pump - Disassemble - Auxiliary Pump (Type 2)
TH48-E70 Petroleum Transmission Safety Messages
An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050} An Updated Troubleshooting Procedure for the Caterpillar Regeneration System Is Available{1050}
C18 Power Module Winding - Test
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Solenoid - Test
3512B Engine Instrument Panel
2008/09/08 Replace the Connecting Rod Bearings According to the Operation and Maintenance Manual {1219, 1225}
3500 Generator Sets Generator Load - Check
C4.4 Generator Set Engines Starting Aid (Glow Plug) Relay Circuit - Test
Troubleshooting a Loss of Combustion with the Aftertreatment Regeneration Device (ARD) {1088} Troubleshooting a Loss of Combustion with the Aftertreatment Regeneration Device (ARD) {1088}
2008/09/29 Procedure to Repair a Service Meter that Runs Constantly {1426, 4462}
3500 Generator Sets Engine Air Cleaner Service Indicator - Inspect
3512B Generator Set Engine Event Codes
3500B Engines Auxiliary Water Pump - Assemble - Auxiliary Pump (Type 2)
3412, 3412C, and 3412E Generator Set Engines Speed Control - Test
3512B Generator Set Engine Configuration Parameters
3412, 3412C, and 3412E Generator Set Engines Fuel Rack Position Sensor - Calibrate
Procedure for Powering the Battery Charger Continuously{751B} Procedure for Powering the Battery Charger Continuously{751B}
Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N} Clean Gas Induction (CGI) Line Upgrade{1061, 1087, 108N}
3412, 3412C, and 3412E Generator Set Engines Speed Control (PWM) - Test
G3600 Engines Welding Precaution
2008/10/01 Diagnostic Code Occurring on C11 and C13 On-Highway Engines {1901, 1920}
Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056} Filtration Procedure For Cold Planer Hydraulic Oil {0680, 0738, 0768, 5050, 5056}
3512B Engine Configuration Parameters