Diagnostic Trouble Codes
The following tables list the diagnostic codes for the Implement ECM. When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.
Show/hide table
Diagnostic Trouble Codes For Implement ECM | ||
---|---|---|
DTC | Description | Procedure |
41-3 | 8 Volt DC Supply: Voltage Above Normal | Electrical Power Supply - Test |
41-4 | 8 Volt DC Supply: Voltage Below Normal | Electrical Power Supply - Test |
96-3 | Fuel Level Sensor: Voltage Above Normal | Sensor Signal ( Analog Active) - Test |
96-4 | Fuel Level Sensor: Voltage Below Normal | Sensor Signal ( Analog Active) - Test |
168-2 | Electrical System Voltage: Data Erratic, Intermittent, or Incorrect | Electrical Power Supply - Test |
168-3 | Electrical System Voltage: Voltage Above Normal | Electrical Power Supply - Test |
168-4 | Electrical System Voltage: Voltage Below Normal | Electrical Power Supply - Test |
246-9 | Proprietary CAN Data Link: Abnormal Update Rate | CAN Data Link - Test |
246-14 | Proprietary CAN Data Link: Special Instruction | CAN Data Link - Test |
247-9 | SAE J1939 Data Link: Abnormal Update Rate | CAN Data Link - Test |
247-14 | SAE J1939 Data Link: Special Instruction | CAN Data Link - Test |
262-3 | 5 Volt Sensor DC Power Supply: Voltage Above Normal | Sensor Supply - Test |
262-4 | 5 Volt Sensor DC Power Supply: Voltage Above Normal | Sensor Supply - Test |
296-9 | Transmission Control: Abnormal Update Rate | |
296-9 | Transmission Control: Special Instruction | |
490-3 | Implement Lockout Switch: Voltage Above Normal | Operator Control Switch (Switch To Ground) - Test |
490-4 | Implement Lockout Switch: Voltage Below Normal | Operator Control Switch (Switch To Ground) - Test |
497-3 | Tilt Right Solenoid: Voltage Above Normal | Solenoid Valve - Test |
497-5 | Tilt Right Solenoid: Current Below Normal | Solenoid Valve - Test |
497-6 | Tilt Right Solenoid: Current Above Normal | Solenoid Valve - Test |
497-13 | Tilt Right Solenoid: Out of Calibration | Solenoid Valve - Test |
498-3 | Tilt Left Solenoid: Voltage Above Normal | Solenoid Valve - Test |
498-5 | Tilt Left Solenoid: Current Below Normal | Solenoid Valve - Test |
498-6 | Tilt Left Solenoid: Current Above Normal | Solenoid Valve - Test |
498-13 | Tilt Left Solenoid: Out of Calibration | Solenoid Valve - Test |
588-9 | Monitoring System Display: Abnormal Update Rate | |
588-14 | Monitoring System Display: Special Instruction | |
590-9 | Engine Control Module: Abnormal Update Rate | CAN Data Link - Test |
590-14 | Engine Control Module: Special Instruction | CAN Data Link - Test |
600-3 | Hydraulic Oil Temperature Sensor: Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
600-4 | Hydraulic Oil Temperature Sensor: Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
779-3 | Cab Air Temperature Sensor: Voltage Above Normal | |
779-4 | Cab Air Temperature Sensor: Voltage Below Normal | |
874-3 | Mode Select Switch: Voltage Above Normal | Operator Control Switch (Switch To Ground) - Test |
874-4 | Mode Select Switch: Voltage Below Normal | Operator Control Switch (Switch To Ground) - Test |
875-3 | Manual Select Switch: Voltage Above Normal | Operator Control Switch (Switch To Ground) - Test |
875-4 | Manual Select Switch: Voltage Below Normal | Operator Control Switch (Switch To Ground) - Test |
880-3 | Ripper Raise/Lower Lever Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
880-4 | Ripper Raise/Lower Lever Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
880-8 | Ripper Raise/Lower Lever Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
880-13 | Ripper Raise/Lower Lever Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
882-3 | Implement Lockout Solenoid: Voltage Above Normal | Solenoid Valve (Switch Controlled) - Test |
882-5 | Implement Lockout Solenoid: Current Below Normal | Solenoid Valve (Switch Controlled) - Test |
882-6 | Implement Lockout Solenoid: Current Above Normal | Solenoid Valve (Switch Controlled) - Test |
888-3 | Ripper Shank Lower Solenoid: Voltage Above Normal | Solenoid Valve - Test |
888-5 | Ripper Shank Lower Solenoid: Current Below Normal | Solenoid Valve - Test |
888-6 | Ripper Shank Lower Solenoid: Current Above Normal | Solenoid Valve - Test |
888-13 | Ripper Shank Lower Solenoid: Out of Calibration | Solenoid Valve - Test |
889-3 | Ripper Shank Raise Solenoid: Voltage Above Normal | Solenoid Valve - Test |
889-5 | Ripper Shank Raise Solenoid: Current Below Normal | Solenoid Valve - Test |
889-6 | Ripper Shank Raise Solenoid: Current Above Normal | Solenoid Valve - Test |
889-13 | Ripper Shank Raise Solenoid: Out of Calibration | Solenoid Valve - Test |
967-6 | Machine Application: Abnormal Update Rate | |
1078-3 | Blade Control Handle Lift Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
1078-4 | Blade Control Handle Lift Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
1078-8 | Blade Control Handle Lift Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1078-13 | Blade Control Handle Raise/Lower Position Sensor: Out Of Calibration | Sensor Signal (PWM) - Test |
1079-3 | Blade Control Handle Tilt Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
1079-4 | Blade Control Handle Tilt Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
1079-8 | Blade Control Handle Tilt Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1079-13 | Blade Control Handle Tilt Position Sensor: Out Of Calibration | Sensor Signal (PWM) - Test |
1197-3 | Blade Lower Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1197-5 | Blade Lower Solenoid: Current Below Normal | Solenoid Valve - Test |
1197-6 | Blade Lower Solenoid: Current Above Normal | Solenoid Valve - Test |
1197-13 | Blade Lower Solenoid: Out of Calibration | Solenoid Valve - Test |
1198-3 | Blade Raise Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1198-5 | Blade Raise Solenoid: Current Below Normal | Solenoid Valve - Test |
1198-6 | Blade Raise Solenoid: Current Above Normal | Solenoid Valve - Test |
1198-13 | Blade Raise Solenoid: Out of Calibration | Solenoid Valve - Test |
1326-2 | ECM Location Code: Erratic, Intermittent, or Incorrect | ECM Location Code - Test |
1393-4 | Output Driver Enable Line: Voltage Below Normal | |
1435-9 | System Master Control Module: Abnormal Update Rate | |
1435-14 | System Master Control Module: Special Instruction | |
1450-3 | Main Hydraulic Pump Oil Pressure Sensor: Voltage Above Normal | Sensor Signal (Analog, Active) - Test |
1450-4 | Main Hydraulic Pump Oil Pressure Sensor: Voltage Below Normal | Sensor Signal (Analog, Active) - Test |
1450-8 | Main Hydraulic Pump Oil Pressure Sensor: Abnormal Frequency, Pulse Width, or Period | |
1482-3 | 10 Volt Sensor DC Power Supply: Voltage Above Normal | Sensor Supply - Test |
1482-4 | 10 Volt Sensor DC Power Supply: Voltage Below Normal | Sensor Supply - Test |
1603-9 | Machine Control Module: Abnormal Update Rate | CAN Data Link - Test |
1603-14 | Machine Control Module: Special Instruction | CAN Data Link - Test |
1834-2 | Ignition Key Switch: Data Erratic, Intermittent, or Incorrect | |
1870-3 | Blade Control Handle Thumb Rocker Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
1870-4 | Blade Control Handle Thumb Rocker Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
1870-8 | Blade Control Handle Thumb Rocker Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1870-13 | Blade Control Handle Thumb Rocker Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
1871-3 | Blade Quick Drop Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1871-5 | Blade Quick Drop Solenoid: Current Below Normal | Solenoid Valve - Test |
1871-6 | Blade Quick Drop Solenoid: Current Above Normal | Solenoid Valve - Test |
1874-3 | Winch Lockout Switch: Voltage Above Normal | Operator Control Switch (Switch To Ground) - Test |
1874-4 | Winch Lockout Switch: Voltage Below Normal | Operator Control Switch (Switch To Ground) - Test |
1881-3 | Winch Control Handle Spool In/Out Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
1881-4 | Winch Control Handle Spool In/Out Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
1881-8 | Winch Control Handle Spool In/Out Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1881-13 | Winch Control Handle Spool In/Out Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
1884-3 | Winch Spool In Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1884-5 | Winch Spool In Solenoid: Current Below Normal | Solenoid Valve - Test |
1884-6 | Winch Spool In Solenoid: Current Above Normal | Solenoid Valve - Test |
1884-13 | Winch Spool In Solenoid: Out of Calibration | Solenoid Valve - Test |
1885-3 | Winch Spool Out Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1885-5 | Winch Spool Out Solenoid: Current Below Normal | Solenoid Valve - Test |
1885-6 | Winch Spool Out Solenoid: Current Above Normal | Solenoid Valve - Test |
1885-13 | Winch Spool Out Solenoid: Out of Calibration | Solenoid Valve - Test |
1887-3 | Winch Spool Out Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1887-5 | Winch Spool Out Solenoid: Current Below Normal | Solenoid Valve - Test |
1887-6 | Winch Spool Out Solenoid: Current Above Normal | Solenoid Valve - Test |
1933-3 | Blade Angle Left Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1933-5 | Blade Angle Left Solenoid: Current Below Normal | Solenoid Valve - Test |
1933-6 | Blade Angle Left Solenoid: Current Above Normal | Solenoid Valve - Test |
1933-13 | Blade Angle Left Solenoid: Out of Calibration | Solenoid Valve - Test |
1934-3 | Blade Angle Right Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1934-5 | Blade Angle Right Solenoid: Current Below Normal | Solenoid Valve - Test |
1934-6 | Blade Angle Right Solenoid: Current Above Normal | Solenoid Valve - Test |
1934-13 | Blade Angle Right Solenoid: Out of Calibration | Solenoid Valve - Test |
1945-2 | Left GPS Receiver: Data Erratic, Intermittent, or Incorrect | Sensor (Data Link Type) - Test |
1945-9 | Left GPS Receiver: Abnormal Update Rate | Sensor (Data Link Type) - Test |
1946-2 | Right GPS Receiver: Data Erratic, Intermittent, or Incorrect | Sensor (Data Link Type) - Test |
1946-9 | Right GPS Receiver: Abnormal Update Rate | Sensor (Data Link Type) - Test |
1952-2 | Chassis Angle Sensor: Erratic, Intermittent, or Incorrect | Sensor (Data Link Type) - Test |
1952-9 | Chassis Angle Sensor: Abnormal Update Rate | Sensor (Data Link Type) - Test |
1952-13 | Chassis Angle Sensor: Out of Calibration | Sensor (Data Link Type) - Test |
1953-2 | Grade Control System Display: Data Erratic, Intermittent, or Incorrect | |
1953-9 | Chassis Angle Sensor: Abnormal Update Rate | |
1964-13 | Lift Cylinder Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
1965-3 | Tilt Cylinder Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
1965-4 | Tilt Cylinder Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
1965-8 | Tilt Cylinder Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1965-13 | Tilt Cylinder Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
2110-2 | Machine Pitch Sensor: Erratic, Intermittent, or Incorrect | Sensor (Data Link Type) - Test |
2110-9 | Machine Pitch Sensor: Abnormal Update Rate | Sensor (Data Link Type) - Test |
2110-13 | Machine Pitch Sensor: Out of Calibration | Sensor (Data Link Type) - Test |
2110-14 | Machine Pitch Sensor: Special Instruction | Sensor (Data Link Type) - Test |
2114-3 | Blade Control Handle Trigger Switch: Voltage Above Normal | Operator Control Switch (Switch To Ground) - Test |
2114-4 | Blade Control Handle Trigger Switch: Voltage Below Normal | Operator Control Switch (Switch To Ground) - Test |
2234-3 | Hydraulic Pump Boost Pressure Solenoid: Voltage Above Normal | Solenoid Valve - Test |
2234-5 | Hydraulic Pump Boost Pressure Solenoid: Current Below Normal | Solenoid Valve - Test |
2234-6 | Hydraulic Pump Boost Pressure Solenoid: Current Above Normal | Solenoid Valve - Test |
2268-3 | Winch Free Spool Solenoid: Voltage Above Normal | Solenoid Valve - Test |
2268-5 | Winch Free Spool Solenoid: Current Below Normal | Solenoid Valve - Test |
2268-6 | Winch Free Spool Solenoid: Current Above Normal | Solenoid Valve - Test |
2300-9 | Switch Panel: Abnormal Update Rate | |
2348-9 | SAE J1939 Data Link #2: Abnormal Update Rate | CAN Data Link - Test |
2348-14 | SAE J1939 Data Link #2: Special Instruction | CAN Data Link - Test |
2357-3 | Air Conditioner Evaporator Coil Temperature Sensor: Voltage Above Normal | Sensor Signal (Analog, Passive) - Test |
2357-4 | Air Conditioner Evaporator Coil Temperature Sensor: Voltage Below Normal | Sensor Signal (Analog, Passive) - Test |
2440-3 | Winch Brake Solenoid: Voltage Above Normal | Solenoid Valve - Test |
2440-5 | Winch Brake Solenoid: Current Below Normal | Solenoid Valve - Test |
2440-6 | Winch Brake Solenoid: Current Above Normal | Solenoid Valve - Test |
2661-3 | Cab Air Temperature Control: Voltage Above Normal | |
2661-4 | Cab Air Temperature Control: Voltage Below Normal | |
2663-3 | Cab Ventilation Duct Temperature Sensor: Voltage Above Normal | |
2663-4 | Cab Ventilation Duct Temperature Sensor: Voltage Below Normal | |
2671-3 | Air Conditioner Compressor Clutch Solenoid: Voltage Above Normal | Solenoid Valve - Test |
2671-5 | Air Conditioner Compressor Clutch Solenoid: Current Below Normal | Solenoid Valve - Test |
2671-6 | Air Conditioner Compressor Clutch Solenoid: Current Above Normal | Solenoid Valve - Test |
2811-3 | Cab Blower Speed Control: Voltage Above Normal | |
2811-4 | Cab Blower Speed Control: Voltage Below Normal | |
3423-9 | Grade Control System: Abnormal Update Rate | |
3423-14 | Grade Control System: Special Instruction | |
3697–2 | Blade Rotation Angle Sensor: Data Erratic, Intermittent, or Incorrect | |
3697–9 | Blade Rotation Angle Sensor: Abnormal Update Rate | |
3744-3 | Winch Control Handle Brake/Free Spool Position Sensor: Voltage Above Normal | Sensor Signal (PWM) - Test |
3744-4 | Winch Control Handle Brake/Free Spool Position Sensor: Voltage Below Normal | Sensor Signal (PWM) - Test |
3744-8 | Winch Control Handle Brake/Free Spool Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
3744–13 | Winch Control Handle Brake/Free Spool Position Sensor: Out of Calibration | Sensor Signal (PWM) - Test |
3747-3 | Winch Main Pressure Solenoid: Voltage Above Normal | Solenoid Valve - Test |
3747-5 | Winch Main Pressure Solenoid: Current Below Normal | Solenoid Valve - Test |
3747-6 | Winch Main Pressure Solenoid: Current Above Normal | Solenoid Valve - Test |
3753-3 | Winch Supply Boost Accumulator Solenoid: Voltage Above Normal | Solenoid Valve - Test |
3753-5 | Winch Supply Boost Accumulator Solenoid: Current Below Normal | Solenoid Valve - Test |
3753-6 | Winch Supply Boost Accumulator Solenoid: Current Above Normal | Solenoid Valve - Test |
3797-3 | Operator Seat Belt Switch: Voltage Above Normal | |
3797-4 | Operator Seat Belt Switch: Voltage Below Normal | |
4011-2 | Air Conditioner #1 Condenser Fan #1 Speed Sensor: Data Erratic, Intermittent, or Incorrect | |
4011-8 | Air Conditioner #1 Condenser Fan #1 Speed Sensor: Abnormal Frequency, Pulse Width, or Period | |
4012-2 | Air Conditioner #1 Condenser Fan #2 Speed Sensor: Data Erratic, Intermittent, or Incorrect | |
4012-8 | Air Conditioner #1 Condenser Fan #2 Speed Sensor: Abnormal Frequency, Pulse Width, or Period | |
4019-3 | Air Conditioner Suction Pressure Sensor: Voltage Above Normal | |
4019-4 | Air Conditioner Suction Pressure Sensor: Voltage Below Normal | |
4019-8 | Air Conditioner Suction Pressure Sensor: Abnormal Frequency, Pulse Width, or Period | |
4022-3 | Air Conditioner Compressor Discharge Pressure Sensor: Voltage Above Normal | |
4022-4 | Air Conditioner Compressor Discharge Pressure Sensor: Voltage Below Normal | |
4022-8 | Air Conditioner Compressor Discharge Pressure Sensor: Abnormal Frequency, Pulse Width, or Period | |
4257-13 | Grade Control Machine Measure Up: Out Of Calibration | |
4651-2 | Blade Inertial Measurement Sensor: Data Erratic, Intermittent, or Incorrect | CAN Data Link - Test |
4651-9 | Blade Inertial Measurement Sensor: Abnormal Update Rate | CAN Data Link - Test |
4651-13 | Blade Inertial Measurement Sensor: Out of Calibration | CAN Data Link - Test |
5102-3 | Cab Air Pressure Sensor: Voltage Above Normal | |
5102-4 | Cab Air Pressure Sensor: Voltage Below Normal | |
5407-13 | Tool Automation Implement Valve: Out of Calibration | Solenoid Valve - Test |
5805-2 | Communication Gateway: Data Erratic, Intermittent, or Incorrect | |
5805-9 | Communication Gateway: Abnormal Update Rate | |
5884-2 | GPS Corrections Radio: Data Erratic, Intermittent, or Incorrect | |
5884-9 | GPS Corrections Radio: Abnormal Update Rate | |
5885-2 | Blade Lift Arm Inertial Measurement Sensor: Data Erratic, Intermittent, or Incorrect | |
5885-9 | Blade Lift Arm Inertial Measurement Sensor: Abnormal Update Rate |
The following tables list the diagnostic codes for the Power Train ECM. When a diagnostic code becomes active, refer to the Troubleshooting section of this manual for a specific troubleshooting procedure.
Show/hide table
Diagnostic Trouble Codes For The Power Train ECM | ||
---|---|---|
DTC | Description | Procedure |
41-3 | 8 Volt DC Supply: Voltage Above Normal | Sensor Supply - Test |
41-4 | 8 Volt DC Supply: Voltage Below Normal | Sensor Supply - Test |
70-2 | Parking Brake Switch: Data Erratic, Intermittent, or Incorrect | Operator Control Switch (Switch to Ground) - Test |
168-2 | Electrical System Voltage: Erratic, Intermittent, or Incorrect | Electrical Power Supply - Test |
168-3 | Electrical System Voltage: Voltage Above Normal | Electrical Power Supply - Test |
168-4 | Electrical System Voltage: Voltage Below Normal | Electrical Power Supply - Test |
177-3 | Transmission Oil Temperature Sensor: Voltage Above Normal | Sensor Signal ( Analog Passive) - Test |
177-4 | Transmission Oil Temperature Sensor: Voltage Below Normal | Sensor Signal ( Analog Passive) - Test |
190-2 | Engine Speed Sensor: Data Erratic, Intermittent, or Incorrect | |
190-8 | Engine Speed Sensor: Abnormal Frequency, Pulse Width, or Period | |
246-9 | CAN Data Link: Abnormal Update Rate | |
247-9 | SAE J1939 Data Link: Abnormal Update Rate | CAN Data Link - Test |
247-14 | SAE J1939 Data Link: Special Instruction | CAN Data Link - Test |
262-3 | 5 Volt Sensor DC Power Supply: Voltage Above Normal | |
262-4 | 5 Volt Sensor DC Power Supply: Voltage Below Normal | |
268-2 | Programmed Parameter Fault: Erratic, Intermittent, or Incorrect | Parameter - Test |
473-3 | Charge Pressure Sensor: Voltage Above Normal | |
473-4 | Charge Pressure Sensor: Voltage Below Normal | |
585-2 | Transmission Output Speed Sensor #1: Erratic, Intermittent, or Incorrect | Speed Sensor - Test |
585-3 | Transmission Output Speed Sensor #1: Voltage Above Normal | Speed Sensor - Test |
585-4 | Transmission Output Speed Sensor #1: Voltage Below Normal | Speed Sensor - Test |
585-8 | Transmission Output Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period | |
588-9 | Monitoring System Display: Abnormal Update Rate | CAN Data Link - Test |
588-14 | Monitoring System Display: Special Instruction | CAN Data Link - Test |
590-9 | Engine Control Module: Abnormal Update Rate | CAN Data Link - Test |
590-14 | Engine Control Module: Special Instruction | CAN Data Link - Test |
596-9 | Implement Control: Abnormal Update Rate | CAN Data Link - Test |
596-14 | Implement Control: Special Instruction | CAN Data Link - Test |
672-2 | Torque Converter Output Speed Sensor: Erratic, Intermittent, or Incorrect | Speed Sensor - Test |
672-3 | Torque Converter Output Speed Sensor: Voltage Above Normal | Speed Sensor - Test |
672-4 | Torque Converter Output Speed Sensor: Voltage Below Normal | Speed Sensor - Test |
672-8 | Torque Converter Output Speed Sensor: Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
673-2 | Transmission Output Speed Sensor #2: Erratic, Intermittent, or Incorrect | Speed Sensor - Test |
673-3 | Transmission Output Speed Sensor #2: Voltage Above Normal | Speed Sensor - Test |
673-4 | Transmission Output Speed Sensor #2: Voltage Below Normal | Speed Sensor - Test |
673-8 | Transmission Output Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
674-2 | Transmission Intermediate Speed Sensor #1: Erratic, Intermittent, or Incorrect | Speed Sensor - Test |
674-3 | Transmission Intermediate Speed Sensor #1: Voltage Above Normal | Speed Sensor - Test |
674-4 | Transmission Intermediate Speed Sensor #1: Voltage Below Normal | Speed Sensor - Test |
674-8 | Transmission Intermediate Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
675-2 | Transmission Intermediate Speed Sensor #2: Erratic, Intermittent, or Incorrect | Speed Sensor - Test |
675-3 | Transmission Intermediate Speed Sensor #2: Voltage Above Normal | Speed Sensor - Test |
675-4 | Transmission Intermediate Speed Sensor #2: Voltage Below Normal | Speed Sensor - Test |
675-8 | Transmission Intermediate Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period | Speed Sensor - Test |
681-3 | Parking Brake Solenoid: Voltage Above Normal | Solenoid Valve (Switch Controlled) - Test |
681-4 | Parking Brake Solenoid: Voltage Below Normal | Solenoid Valve (Switch Controlled) - Test |
681-5 | Parking Brake Solenoid: Current Below Normal | Solenoid Valve (Switch Controlled) - Test |
681-6 | Parking Brake Solenoid: Current Above Normal | Solenoid Valve (Switch Controlled) - Test |
709-3 | Transmission Lockup Clutch Solenoid: Voltage Above Normal | Solenoid Valve - Test |
709-5 | Transmission Lockup Clutch Solenoid: Current Below Normal | Solenoid Valve - Test |
709-6 | Transmission Lockup Clutch Solenoid: Current Above Normal | Solenoid Valve - Test |
718-13 | Transmission System: Out of Calibration | Perform the "Transmission Clutch Fill Calibration" |
726-3 | Right Steering Solenoid: Voltage Above Normal | Solenoid Valve - Test |
726-5 | Right Steering Solenoid: Current Below Normal | Solenoid Valve - Test |
726-6 | Right Steering Solenoid: Current Above Normal | Solenoid Valve - Test |
726-13 | Right Steering Solenoid: Out of Calibration | Solenoid Valve - Test |
727-3 | Left Steering Solenoid: Voltage Above Normal | Solenoid Valve - Test |
727-5 | Left Steering Solenoid: Current Below Normal | Solenoid Valve - Test |
727-6 | Left Steering Solenoid: Current Above Normal | Solenoid Valve - Test |
727-13 | Left Steering Solenoid: Out of Calibration | Solenoid Valve - Test |
826-3 | Torque Converter Oil Temperature Sensor: Voltage Above Normal | Sensor Signal ( Analog Passive) - Test |
826-4 | Torque Converter Oil Temperature Sensor: Voltage Below Normal | Sensor Signal ( Analog Passive) - Test |
1326-2 | ECM Location Code: Erratic, Intermittent, or Incorrect | ECM Location Code - Test |
1401-3 | Transmission Solenoid 1: Voltage Above Normal | Solenoid Valve - Test |
1401-5 | Transmission Solenoid 1: Current Below Normal | Solenoid Valve - Test |
1401-6 | Transmission Solenoid 1: Current Above Normal | Solenoid Valve - Test |
1402-3 | Transmission Solenoid 2: Voltage Above Normal | Solenoid Valve - Test |
1402-5 | Transmission Solenoid 2: Current Below Normal | Solenoid Valve - Test |
1402-6 | Transmission Solenoid 2: Current Above Normal | Solenoid Valve - Test |
1403-3 | Transmission Solenoid 3: Voltage Above Normal | Solenoid Valve - Test |
1403-5 | Transmission Solenoid 3: Current Below Normal | Solenoid Valve - Test |
1403-6 | Transmission Solenoid 3: Current Above Normal | Solenoid Valve - Test |
1404-3 | Transmission Solenoid 4: Voltage Above Normal | Solenoid Valve - Test |
1404-5 | Transmission Solenoid 4: Current Below Normal | Solenoid Valve - Test |
1404-6 | Transmission Solenoid 4: Current Above Normal | Solenoid Valve - Test |
1405-3 | Transmission Solenoid 5: Voltage Above Normal | Solenoid Valve - Test |
1405-5 | Transmission Solenoid 5: Current Below Normal | Solenoid Valve - Test |
1405-6 | Transmission Solenoid 5: Current Above Normal | Solenoid Valve - Test |
1406-3 | Transmission Solenoid 6: Voltage Above Normal | Solenoid Valve - Test |
1406-5 | Transmission Solenoid 6: Current Below Normal | Solenoid Valve - Test |
1406-6 | Transmission Solenoid 6: Current Above Normal | Solenoid Valve - Test |
1469-2 | Steering Motor Speed Sensor #1: Erratic, Intermittent, or Incorrect | Sensor Signal (PWM) - Test |
1469-8 | Steering Motor Speed Sensor #1: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1470-2 | Steering Motor Speed Sensor #2: Erratic, Intermittent, or Incorrect | Sensor Signal (PWM) - Test |
1470-8 | Steering Motor Speed Sensor #2: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1471-3 | Steering Control Position Sensor #1: Voltage Above Normal | Sensor Signal (PWM) - Test |
1471-4 | Steering Control Position Sensor #1: Voltage Below Normal | Sensor Signal (PWM) - Test |
1471-8 | Steering Control Position Sensor #1: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1471-12 | Steering Control Position Sensor #1: Failure | Sensor Signal (PWM) - Test |
1471-13 | Steering Control Position Sensor #1: Out of Calibration | Sensor Signal (PWM) - Test |
1472-3 | Steering Control Position Sensor #2: Voltage Above Normal | Sensor Signal (PWM) - Test |
1472-4 | Steering Control Position Sensor #2: Voltage Below Normal | Sensor Signal (PWM) - Test |
1472-8 | Steering Control Position Sensor #2: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
1472-12 | Steering Control Position Sensor #2: Bad Device or Component | Sensor Signal (PWM) - Test |
1472-13 | Steering Control Position Sensor #2: Out of Calibration | Sensor Signal (PWM) - Test |
1482-3 | 10 Volt Sensor DC Power Supply: Voltage Above Normal | Sensor Supply - Test |
1482-4 | 10 Volt Sensor DC Power Supply : Voltage Below Normal | Sensor Supply - Test |
1579-3 | Transmission Lube Flow Valve Solenoid: Voltage Above Normal | Solenoid Valve - Test |
1579-5 | Transmission Lube Flow Valve Solenoid: Current Below Normal | Solenoid Valve - Test |
1579-6 | Transmission Lube Flow Valve Solenoid: Current Above Normal | Solenoid Valve - Test |
2300-9 | Switch Panel: Abnormal Update Rate | |
2348-9 | SAE J1939 Data Link #2: Abnormal Update Rate | CAN Data Link - Test |
2348-14 | SAE J1939 Data Link #2: Special Instruction | CAN Data Link - Test |
2500-8 | Power train Speed Range Control Position Sensor: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
2596-3 | Brake Pressure Modulation Solenoid: Voltage Above Normal | Solenoid Valve (Switch Controlled) - Test |
2596-5 | Brake Pressure Modulation Solenoid: Current Below Normal | Solenoid Valve (Switch Controlled) - Test |
2596-6 | Brake Pressure Modulation Solenoid: Current Above Normal | Solenoid Valve (Switch Controlled) - Test |
2596-13 | Brake Pressure Modulation Solenoid: Out of Calibration | Solenoid Valve (Switch Controlled) - Test |
2993-3 | Direction Selector Position Sensor #1: Voltage Above Normal | Sensor Signal (PWM) - Test |
2993-4 | Direction Selector Position Sensor #1: Voltage Below Normal | Sensor Signal (PWM) - Test |
2993-8 | Direction Selector Position Sensor #1: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
2994-3 | Direction Selector Position Sensor #2: Voltage Above Normal | Sensor Signal (PWM) - Test |
2994-4 | Direction Selector Position Sensor #2: Voltage Below Normal | Sensor Signal (PWM) - Test |
2994-8 | Direction Selector Position Sensor #2: Abnormal Frequency, Pulse Width, or Period | Sensor Signal (PWM) - Test |
3210-3 | Transmission Pump Bypass Solenoid: Voltage Above Normal | Solenoid Valve - Test |
3210-5 | Transmission Pump Bypass Solenoid: Current Below Normal | Solenoid Valve - Test |
3210-6 | Transmission Pump Bypass Solenoid: Current Above Normal | Solenoid Valve - Test |
3467-3 | Main Power Relay: Voltage Above Normal | Relay -Test |
3467-5 | Main Power Relay: Current Below Normal | Relay -Test |
3467-6 | Main Power Relay: Current Above Normal | Relay -Test |
3527-12 | Direction Selector: Failure | Switch Circuits - Test |
3642-2 | Operator Speed Set/Recall Switch: Erratic, Intermittent, or Incorrect | Switch Circuits - Test |
3652-3 | Steering Pump Oil Pressure #1 Sensor: Voltage Above Normal | |
3652-4 | Steering Pump Oil Pressure #1 Sensor: Voltage Below Normal | |
3652-8 | Steering Pump Oil Pressure #1 Sensor: Abnormal Frequency, Pulse Width, or Period | |
3653-3 | Steering Pump Oil Pressure #2 Sensor: Voltage Above Normal | |
3653-4 | Steering Pump Oil Pressure #2 Sensor: Voltage Below Normal | |
3653-8 | Steering Pump Oil Pressure #2 Sensor: Abnormal Frequency, Pulse Width, or Period | |
3657-2 | Operator In Seat Sensor: Erratic, Intermittent, or Incorrect | Sensor Signal ( Analog Passive) - Test |
3657-3 | Operator In Seat Sensor: Voltage Above Normal | Sensor Signal ( Analog Passive) - Test |
3657-4 | Operator In Seat Sensor: Voltage Below Normal | Sensor Signal ( Analog Passive) - Test |
5001-3 | Right Pedal Position Sensor: Voltage Above Normal | |
5001-4 | Right Pedal Position Sensor: Voltage Below Normal | |
5001-8 | Right Pedal Position Sensor: Abnormal Frequency, Pulse Width, or Period | |
5002-3 | Left Pedal Position Sensor: Voltage Above Normal | |
5002-4 | Left Pedal Position Sensor: Voltage Below Normal | |
5002-8 | Left Pedal Position Sensor: Abnormal Frequency, Pulse Width, or Period | |
5002-13 | Left Pedal Position Sensor: Out of Calibration | |
5580-2 | Power Train Operator Interface Module: Erratic, Intermittent, or Incorrect | |
5580-9 | Power Train Operator Interface Module: Abnormal Update Rate | |
5580-14 | Power Train Operator Interface Module: Special Instruction |
Caterpillar Information System:
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Air Inlet and Exhaust System Operation
New Troubleshooting Procedure for the Low Steering Pilot Pressure Code Is Now Used for Certain 854K Wheel Dozers and 992K Wheel Loaders {0732, 4300, 4306, 5070, 5073} New Troubleshooting Procedure for the Low Steering Pilot Pressure Code Is Now Used for Certain 854K Wheel Dozers and 992K Wheel Loaders {0732, 4300, 4306, 5070, 5073}
MD6250 Rotary Drill Systems Rotary Head - Test and Adjust
MD6250 Rotary Drill Systems Travel System - Test and Adjust
MD6250 Rotary Drill Systems Mast - Test and Adjust
MD6250 Rotary Drill Systems Leveling System - Test and Adjust
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Model View Illustrations
New Engine Software is Now Available for Certain Track-Type Tractor Engines {1902, 1920, 7610, 7620} New Engine Software is Now Available for Certain Track-Type Tractor Engines {1902, 1920, 7610, 7620}
D8T and D9T Track-Type Tractors ECM - Configure
PL61 Pipelayers Engine Supplement Engine Oil Filter and Base - Remove and Install
Compatibility of The Bulldozer Arrangement, Rear Attachments, and Final Drive Guards of D6T Track-Type Tractors {5163, 6050, 6060, 6310, 7000, 7056} Compatibility of The Bulldozer Arrangement, Rear Attachments, and Final Drive Guards of D6T Track-Type Tractors {5163, 6050, 6060, 6310, 7000, 7056}
D6 Track-Type Tractor Machine Systems Steering Oil Filter and Base - Remove and Install
Exhaust Cooler (NRS) on Certain C7.1 and C6.6 Machine Engines {1061, 1087, 108C} Exhaust Cooler (NRS) on Certain C7.1 and C6.6 Machine Engines {1061, 1087, 108C}
PL61 Pipelayers Engine Supplement Oil Cooler (Engine) - Remove and Install
MD6250 Rotary Drill Systems Counterbalance Valve - Test and Adjust - Mast Raise
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Caterpillar Approved Work Tools
Installation of Counterweight and Ground Level Service Center on Certain D11 Track-Type Tractors {1408, 7056, 7153} Installation of Counterweight and Ground Level Service Center on Certain D11 Track-Type Tractors {1408, 7056, 7153}
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Drive Line Wear Sleeve - Inspect/Replace - MTL Only
D9R Track-Type Tractor Power Train Torque Divider - Disassemble
New Improved Grapple Bucket Pins for Small Wheel Loaders {6101} New Improved Grapple Bucket Pins for Small Wheel Loaders {6101}
C7.1 Engines SCR Catalyst Has Incorrect Inlet Temperature
D9T Track-Type Tractor Machine Systems Battery and Wiring Group
PL61 Pipelayers Engine Supplement Fuel Filter and Base - Remove and Install
D3-Series Compact Track Loaders (CTL), Multi-Terrain Loaders (MTL), and Skid Steer Loaders (SSL) Belts - Inspect/Adjust