Exhaust Manifold - Remove and Install
拆卸步骤
Show/hide table
高温发动机部件可能导致灼伤。 进行发动机保养之前让发动机和部件冷却下来。 |
- 打开发动机检修门.
- 拆下盖 (1) 。 拆下管 (2) 。
Show/hide table
图 1 | g01188562 |
- 断开软管组件 (7) 。 断开软管组件 (6) 。 断开涡轮增压器 (3) 相反一侧上的软管组件。
Show/hide table
图 2 | g01188574 |
- 从涡轮增压器 (3) 上断开软管组件 (4) 。
- 松开管路 (5) 的两端。
- 从发动机 (8) 上断开支架 (9) 。 拆下螺栓 (11) 。 拆下机油加注管 (10) 。
Show/hide table
图 3 | g01188687 |
Show/hide table
图 4 | g01188688 |
- 将适当的起吊设备连接到排气歧管 (13) 和涡轮增压器 (3) 上。 排气歧管 (13) 和涡轮增压器 (3) 的重量约为 34 kg (75 lb)。
Show/hide table
图 5 | g01188694 |
- 拆下螺母 (12) 。 拆下排气歧管 (13) 和涡轮增压器 (3) 。
- 拆下螺母 (14) 。 将涡轮增压器 (3) 与排气歧管 (13) 分开。
Show/hide table
图 6 | g01188698 |
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 4C-5597     | 防粘结剂     | 1     |
- 将涡轮增压器 (3) 定位到排气歧管 (13) 上。 在螺栓上使用工具 (A) 。 安装螺母 (14) 。
Show/hide table
图 7 | g01188698 |
- 在排气歧管螺栓的螺纹上使用工具 (A) 。 将适当的起吊设备连接到排气歧管 (13) 和涡轮增压器 (3) 上。 排气歧管 (13) 和涡轮增压器 (3) 的重量约为34 kg (75 lb)。
Show/hide table
图 8 | g01188694 |
- 安装排气歧管 (13) 和涡轮增压器 (3) 。 安装螺母 (12) 。
- 安装机油加注管 (10) 。 将支架 (9) 连接到发动机 (8) 上。 安装螺栓 (11) 。
Show/hide table
图 9 | g01188688 |
Show/hide table
图 10 | g01188687 |
- 拧紧管路 (5) 的两端。
Show/hide table
图 11 | g01188574 |
- 将软管组件 (4) 安装到涡轮增压器 (3) 上。
- 连接软管组件 (7) 。 连接软管组件 (6) 。 将软管组件连接到涡轮增压器 (3) 的相反一侧。
- 安装管 (2) 。 安装盖 (1) 。
Show/hide table
图 12 | g01188562 |
- 关闭发动机检修门。
Caterpillar Information System:
C32 Marine Engines Rocker Arm and Shaft - Install
C9-XQ300 Rental Generator Set Engine Speed/Timing Sensors - Check/Clean/Calibrate
C32 Marine Engines Rocker Arm and Shaft - Remove
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
C32 Marine Engines Valve Mechanism Cover Base - Remove and Install
3412E and C30 Marine Engines Fuel System Water Separator - Drain
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1779 FMI 06
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
C27 and C32 Generator Set Engines Vibration Damper and Pulley
C32 Marine and Auxiliary Marine Engines Valve Mechanism Cover - Remove and Install
C32 Marine and Auxiliary Marine Engines Housing (Rear) - Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Muffler - Remove and Install
C11 and C13 On-Highway Engines Turbocharger
C11 and C13 On-Highway Engines Air Lines
C27 and C32 Generator Set Engines Flywheel
C11 and C13 On-Highway Engines Camshaft
C15 Petroleum Generator Set Engines Alternator and Regulator
2005/08/15 New Bolt Available to Secure Generator Flex-Plate to Generator Rotor Shaft {3252}
C6.6 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
3126B Generator Set Engine Diagnostic Codes
2005/08/29 A New O-Ring Seal is Now Available for the Crankcase Breather {1317}
C11 and C13 Industrial Engines Engine Oil Filter Base
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Turbocharger - Remove
C11 and C13 On-Highway Engines Engine Oil Cooler