Housing (Rear) - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 4C-9612 | Silicone Sealant | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to the bottom of the rear housing at the junction of the cylinder block and the engine oil pan.
Show/hide table
Illustration 1 g01147138 Show/hide tableIllustration 2 g01147149 - Attach a suitable lifting device to rear housing (4). The weight of rear housing (4) is approximately
84 kg (185 lb) . - Position the gasket on rear housing (4).
- Position rear housing (4) on the cylinder block. Install bolts (3). Tighten bolts (3) in a numerical sequence to a torque of
55 ± 10 N·m (41 ± 7 lb ft) . - Trim the gasket between the rear housing and the cylinder block even with the bottom of the rear housing.
Show/hide table
Illustration 3 g01188205 - Install bolts (2).
- Connect hose assembly (1).
- Install the bolts that hold the engine oil pan to the rear housing.
- Tighten all the bolts that hold the engine oil pan evenly in order to raise the engine oil pan into position.
End By:
- Install the rear gear group. Refer to Disassembly and Assembly, "Gear Group (Rear) - Install".
Caterpillar Information System:
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Muffler - Remove and Install
C32 Marine and Auxiliary Marine Engines Housing (Rear) - Remove
C13 Engine for Combat and Tactical Vehicles Engine Design
C-12 Generator Set Engine CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
G3408C and G3412C Engines Inlet and Exhaust Valve Guides - Remove and Install - New Taller Head
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1779 FMI 05
C32 Marine and Auxiliary Marine Engines Housing (Front) - Install
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1743 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 08
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 03
C32 Marine and Auxiliary Marine Engines Housing (Front) - Remove
C32 Marine and Auxiliary Marine Engines Valve Mechanism Cover - Remove and Install
C27 and C32 Generator Set Engines Vibration Damper and Pulley
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1779 FMI 06
3412E and C30 Marine Engines Fuel System Water Separator - Drain
C32 Marine Engines Valve Mechanism Cover Base - Remove and Install
C13, C15, and C18 Tier 4 Final Engines Valve Mechanism
C32 Marine Engines Rocker Arm and Shaft - Remove
C9-XQ300 Rental Generator Set Engine Speed/Timing Sensors - Check/Clean/Calibrate
C32 Marine Engines Rocker Arm and Shaft - Install
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Exhaust Manifold - Remove and Install
C11 and C13 On-Highway Engines Turbocharger