Housing (Front) - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 4C-9612 | Silicone Sealant | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to the bottom of front housing (10) at the junction of the cylinder block and the engine oil pan.
- Attach a suitable lifting device to front housing (10). The weight of front housing (10) is approximately
67 kg (148 lb) . Position the gasket and front housing (10) on the dowel pins on the cylinder block. - Install bolts (11) and bolts (12).
- Trim the gasket between the front housing and the cylinder block even with the bottom of the front housing.
- Install adapters (9).
Show/hide table
Illustration 2 g01188104 - Connect flanges (8).
Show/hide table
Illustration 3 g01147758 Show/hide tableIllustration 4 g01151441 - Install dampers (7) and bolts (6).
- Tighten the bolts to a torque of
240 ± 40 N·m (177 ± 30 lb ft) . Tighten the bolts in the following sequence: 1, 4, 2, 5, 3, 6, 1, 4.Show/hide tableIllustration 5 g01188101 - Reposition fuel filter assembly (5) and tighten bolts (3).
- Connect harness assembly (2).
- Install covers (1).
Show/hide table
Illustration 1 | g01188105 |
End By:
- Install the front engine support. Refer to Disassembly and Assembly, "Engine Trunnion - Remove and Install".
- Install the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Install".
- Install the crankshaft front seal. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the auxiliary water pump. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
- Install the water pump. Refer to Disassembly and Assembly, "Water Pump - Install".
Caterpillar Information System:
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1743 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 08
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 04
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 03
C32 Marine and Auxiliary Marine Engines Housing (Front) - Remove
C-12 Generator Set Engine CID 0262 FMI 03 5 Volt Sensor DC Power Supply short to +batt
C15 Generator Sets Cold Weather Starting
C9-XQ300 Rental Generator Set Fuel Related Components in Cold Weather
C9-XQ300 Rental Generator Set Before Towing
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Electric Starting Motor - Remove and Install
TH48-E80 Petroleum Transmission Power Train Electronic Control System MID 027 - CID 0707 - FMI 03
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 0774 FMI 02
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1779 FMI 05
G3408C and G3412C Engines Inlet and Exhaust Valve Guides - Remove and Install - New Taller Head
C-12 Generator Set Engine CID 0262 FMI 04 5 Volt Sensor DC Power Supply short to ground
C13 Engine for Combat and Tactical Vehicles Engine Design
C32 Marine and Auxiliary Marine Engines Housing (Rear) - Remove
345C MHPU Mobile Hydraulic Power Unit Engine Supplement Muffler - Remove and Install
C32 Marine and Auxiliary Marine Engines Housing (Rear) - Install
C32 Marine and Auxiliary Marine Engines Valve Mechanism Cover - Remove and Install
C27 and C32 Generator Set Engines Vibration Damper and Pulley
C4.4 and C6.6 Engines for Caterpillar Built Machines Engine Speed/Timing Sensor Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines CID 1779 FMI 06
3412E and C30 Marine Engines Fuel System Water Separator - Drain