Parking Brake Actuator - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-0520     | Driver Group     | 1     |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Install O-ring seal (16) and seal (15) to cylinder assembly (3) .
Show/hide table
Illustration 1 | g00399204 |
- Install O-ring seal (14) and felt wiper seal (13) to piston assembly (12) .
Show/hide table
Illustration 2 | g00399203 |
- Use a press to install piston assembly (12) to cylinder assembly (3) .
Show/hide table
Illustration 3 | g00399922 |
- Install pushrod (6) to cylinder assembly (3) . Install flange nut (11) , nut (10) and spacer sleeve (9) to pushrod (6) .
Show/hide table
Illustration 4 | g00399201 |
- Install dust boot (8) , nut (5) and yoke rod end (7) to pushrod (6) .
Show/hide table
Illustration 5 | g00399200 |
- Install spring (4) to cylinder assembly (3) . Install cover (1) to spring (4) .
Show/hide table
Illustration 6 | g00399199 |
- Use Tool (A) and a press in order to press down on cover (1) . Install eight bolts (2) to cylinder assembly (3) .
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
Show/hide table
Illustration 7 | g00399198 |
End By: Install the parking brake actuator. Refer to Disassembly and Assembly, "Parking Brake Actuator - Install". The information is in this manual.
Caterpillar Information System:
994D Wheel Loader Power Train Speed Sensor (Torque Converter Output)
D6G Track-Type Tractor Power Train Recoil Spring - Remove and Install
D6G Track-Type Tractor Power Train Hydraulic Track Adjusters - Assemble
Field Installation of Decelerator Pedal{1276} Field Installation of Decelerator Pedal{1276}
D6G Track-Type Tractor Power Train Hydraulic Track Adjusters - Disassemble
854G Wheel Dozer Machine Systems Front Frame and Rear Frame - Connect
854G Wheel Dozer Machine Systems Front Frame and Rear Frame - Separate
613C Series II Wheel Tractor-Scraper Machine Systems Parking Brake Actuator - Disassemble
966G Wheel Loader and 972G Wheel Loader Machine Systems Lift Arms - Install
613C Series II Wheel Tractor-Scraper Machine Systems Parking Brake Actuator - Install
613C Series II Wheel Tractor-Scraper Machine Systems Check Valve (Floor) - Remove
3306B Industrial Engine Electric Starting Motor
D6G Track-Type Tractor Power Train Recoil Spring - Disassemble
953C, 963C and 973C Track-Type Loaders Transmission Electronic Control System Electronic Control Module (ECM) - Replace
994D Wheel Loader Power Train Modulating Valve (Torque Converter Impeller Clutch)
613C Series II Wheel Tractor-Scraper Machine Systems Parking Brake - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Parking Brake - Install
627F Wheel Tractor-Scraper Cooling System Coolant (ELC) - Change
854G Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Remove
854G Wheel Dozer Machine Systems Gear Pump (Implement Pilot) - Install
D6G Track-Type Tractor Power Train Recoil Spring - Assemble
613C Series II Wheel Tractor-Scraper Machine Systems Vane Motor (Elevator) - Remove
966G Wheel Loader and 972G Wheel Loader Machine Systems Pilot Valve (Oil Manifold) - Remove
D6G Track-Type Tractor Power Train Track Roller Frame - Remove