Gauges and Indicators
您的发动机上的仪表可能与下述仪表不同或不具备所有下述仪表。 更多有关仪表组的资料,请参阅原始设备制造商提供的资料。
仪表指示出发动机性能。 确保仪表处于良好的工作状态。 观察仪表一段时间之后,您就能确定正常的运行范围。
仪表读数的显著变化表明潜在的仪表或发动机问题。 即使仪表读数在规格范围内,其读数变化也可能表明存在问题。 确定和纠正导致任何读数显著变化的原因。 请咨询您的卡特彼勒代理商以便获得帮助。
Show/hide table
注意 |
---|
如果显示无机油压力,应将发动机停机。 如果发动机冷却液超出了最高冷却液温度,停止发动机。 否则会导致发动机损坏。 |
Show/hide table
发动机机油压力表 - 冷态发动机起动后,机油压力应在最大值。 |
低怠速时机油压力低是正常的。 如果负载稳定但仪表读数变化,进行以下步骤:
- 卸掉负载。
- 降低发动机转速至低怠速。
- 检查和保持机油油位。
Show/hide table
水套水冷却液温度表 - 压力为103 kPa (15 psi)的加压冷却系统的最高容许温度为110 °C (230 °F)。 在某些情况下可能会有更高的温度。 随着负荷的不同,发动机冷却液温度读数不同。 对于正在使用中的增压系统,读数应永远不能超过沸点。 |
如果发动机在正常范围内运转且有蒸汽生成,则进行下列程序:
- 降低负荷和发动机转速。
- 检查冷却系统是否渗漏。
- 决定是否必须立即关闭发动机,或者是否可以通过降低负载使发动机冷却。
Show/hide table
转速表 - 此表指示发动机转速。 在无负载时,把油门控制杆移动到全油门位置,发动机在高怠速运转。 在最大额定负载下,油门控制杆在全油门位置,发动机在满负载转速下运转。 |
Show/hide table
注意 |
---|
为帮助防止发动机受到损害,切勿超过高怠速转速。 超速可能导致对发动机的严重损害。 发动机可以在高怠速运行而不受损害,但应绝不许超过高怠速转速。 |
注: 高怠速和满负载转速刻印在信息资料铭牌上。
Show/hide table
电流表 - 此仪表指示蓄电池充电电路中的充电或放电量。 仪表指针应运作在 "0"(零)位右侧。 |
Show/hide table
燃油油位 - 此表指示燃油箱中燃油的液位。 通常燃油油位表只在开关处于接通 (ON) 位置时才记录燃油油位。 |
Show/hide table
工时计 - 该仪表指示发动机已运转的总时钟小时数。 |
Caterpillar Information System:
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Maintenance Interval Schedule
3500B Engines Air Inlet and Exhaust Lines
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 1495 - FMI 02 Injector Trim Codes Not Programmed
G3304 and G3306 Engines Carburetor - Remove
G3304 and G3306 Engines Carburetor - Install
C7 On-highway Engine Water Pump - Remove
G3304 and G3306 Engines Valve Lifter - Install
C1.5 and C2.2 Generator Generator - Install
G3304 and G3306 Engines Aftercooler - Install
2003/05/01 Installation Procedure for a Thermocouple in the Exhaust of a Marine Engine {7498}
3054E Industrial Engine Crankshaft Rear Seal - Remove
3618 Engine Driven Equipment - Check
C1.5 and C2.2 Generator Lead Connections
G3304 and G3306 Engines Water Pump - Remove
3054E Industrial Engine Flywheel - Install
G3304 and G3306 Engines Water Pump - Install
G3304 and G3306 Engines Water Pump - Disassemble
Installation Guide for Industrial Electronic Engine Displays General Information
3618 Engine Engine Mounts - Inspect
Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070} Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070}
3044C Industrial Engine Fuel System - Prime
Installation Guide for Industrial Electronic Engine Displays Wiring - General
C7 On-highway Engine Water Pump - Install
3044C Industrial Engine Fuel System Filter - Replace