Flywheel - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | -     | 导向螺栓 (1/2 in - 20 NF X 4 in)     |
2     |
B     | 138-7575     | 连杆支架     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 彻底清洁飞轮壳。 检查曲轴后油封是否泄漏。 如果存在机油泄漏,请参阅拆解和组装手册, "曲轴后油封 - 拆卸"。
- 将齿圈 (3) 在恒温箱中加热至 250 °C (480 °F),以便将齿圈安装到飞轮 (2) 上。 确保齿圈 (3) 的方向正确,并迅速地将齿圈安装到飞轮 (2) 上。
注: 不要使用喷枪加热齿圈。
Show/hide table
图 1 | g00909349 |
Show/hide table
操作已经加热的零件时要坚持戴防护手套。 |
注: 如果从飞轮 (2) 上拆下齿圈 (3) ,标记齿圈 (3) 在飞轮 (2) 上的方向,以便安装新齿圈时可以正确定位。
- 待齿圈冷却后,清洁飞轮 (2) 和齿圈 (3) 。
- 将工具 (A) 安装到曲轴上。 在飞轮 (2) 上安装工具 (B) 和适当的起吊设备,然后将飞轮定位到飞轮壳上。 飞轮的重量约为 54 kg (119 lb)。
Show/hide table
图 2 | g01148312 |
- 安装调整螺钉 (1) 。 拆下工具 (B) 。
- 拆下工具 (A) 。 安装将飞轮 (2) 固定到曲轴上的其余调整螺钉 (1) 。 以 105 N·m (77 lb ft) 的扭矩拧紧调整螺钉 (1) 。
- 检查飞轮 (2) 与曲轴是否对齐。 请参阅测试与调整, "飞轮 - 检查"。
Caterpillar Information System:
G3304 and G3306 Engines Water Pump - Remove
C1.5 and C2.2 Generator Lead Connections
3044C Industrial Engine Gauges and Indicators
CIPI UNDERCARRIAGE Arrangements: 1667049, 2372904, 3Q6481, 6Z7988, 6Z7989, 9Q5032, 9Q5040, 9Q5043, 9Q5046, 9Q5047, 9Q5066, 9Q5074, 9Q5097, 9Q5098, 9Q5116, 9Q5134, 9Q5136, 9Q5142, 9Q5147, 9Q5148, 9Q5149, 9Q5172 and 9Q5204 Maintenance Interval Schedule
3500B Engines Air Inlet and Exhaust Lines
3500B Engines for 776D, 777D, 784C, 785C, 789C and 793C Off-Highway Trucks MID 036 - CID 1495 - FMI 02 Injector Trim Codes Not Programmed
G3304 and G3306 Engines Carburetor - Remove
G3304 and G3306 Engines Carburetor - Install
C7 On-highway Engine Water Pump - Remove
G3304 and G3306 Engines Valve Lifter - Install
C1.5 and C2.2 Generator Generator - Install
G3304 and G3306 Engines Aftercooler - Install
G3304 and G3306 Engines Water Pump - Install
G3304 and G3306 Engines Water Pump - Disassemble
Installation Guide for Industrial Electronic Engine Displays General Information
3618 Engine Engine Mounts - Inspect
Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070} Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070}
3044C Industrial Engine Fuel System - Prime
Installation Guide for Industrial Electronic Engine Displays Wiring - General
C7 On-highway Engine Water Pump - Install
3044C Industrial Engine Fuel System Filter - Replace
C1.5 and C2.2 Generator Leads - Connect
3044C Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C7 On-Highway Engine Air Compressor - Remove and Install