Fuel System Filter - Replace
Show/hide table
渗漏或溅溢到热表面或电气部件上的燃油会引起失火。 为防止可能的伤害,当更换燃油滤清器或油水分离器滤芯时,要将起动开关断开。 应立即将溅溢的燃油清除干净。 |
Show/hide table
注意 |
---|
不要让脏物进入燃油系统。 彻底清洁将要拆开的燃油系统部件的周围区域。 在拆开的燃油系统部件上安放适当的盖。 |
进行本保养之前应先将供油阀转到关闭(OFF)位置。 在燃油滤清器下面放置一个,以便盛接所有可能洒出的燃油。 立即清理溅出的燃油。
- 关闭供油阀。
Show/hide table
图 1 | g01355125 |
(1) 电动燃油充油泵 (2) 燃油滤清器底座 (3) 快速释放固定圈 (4) 燃油滤清器 (5) 沉淀物分离杯 (6) 燃油滤清器排放阀 |
- 清洁燃油滤清器总成的外表面。 打开排放阀 (6) 将冷却液排放到适当的容器内。
- 拆下沉积物分离杯 (5) 。
- 握住燃油滤清器 (4) ,逆时针转到快速释放固定圈 (3) 。 拆下快速释放固定圈 (3) 。 应将旧滤芯拆下并废弃。
Show/hide table
注意 |
---|
不要使用工具来拆下燃油滤清器。 试图使用滤清器扳手或滤清器拆卸带来拆下燃油滤清器会损坏锁环。 |
- 确保滤清器底座清洁。 将新滤芯完全推入滤清器底座内。
Show/hide table
注意 |
---|
安装燃油滤清器之前不要在其中注入燃油。 污染的燃油会加速燃油系统部件的磨损。 |
- 握住燃油滤清器。 将锁环 (3) 安装入位。 顺时针转到锁环以便将燃油滤清器固定到滤清器底座上。
- 彻底清洁沉积物分离杯 (5) 。 检查O形密封圈。 如有必要,更换新的O形密封圈。 将沉淀杯安装到新滤芯上。 用手拧紧沉淀杯。 用手拧紧是唯一应该使用的方法。
- 泵注燃油系统。 请参阅操作与保养手册, "燃油系统 - 充注"。
Caterpillar Information System:
C7 On-highway Engine Water Pump - Install
Installation Guide for Industrial Electronic Engine Displays Wiring - General
3044C Industrial Engine Fuel System - Prime
Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070} Rotating Group Adjustment Instructions for Bosch Rexroth Hydraulic Pumps and Motors {3203, 4351, 5058, 5070}
3618 Engine Engine Mounts - Inspect
Installation Guide for Industrial Electronic Engine Displays General Information
G3304 and G3306 Engines Water Pump - Disassemble
G3304 and G3306 Engines Water Pump - Install
3054E Industrial Engine Flywheel - Install
G3304 and G3306 Engines Water Pump - Remove
C1.5 and C2.2 Generator Lead Connections
3044C Industrial Engine Gauges and Indicators
C1.5 and C2.2 Generator Leads - Connect
3044C Industrial Engine Fuel System Primary Filter/Water Separator - Drain
C7 On-Highway Engine Air Compressor - Remove and Install
330B Excavator Hydraulic System Accumulator (Pilot) - Test and Charge
C7 On-highway Engine Water Pump - Disassemble
C7 On-highway Engine Water Pump - Assemble
C1.5 and C2.2 Generator Rotating Rectifier - Test
Installation Guide for Industrial Electronic Engine Displays Wiring - CAT Data Link (CDL)
3500B and 3500C Marine Propulsion Engines Engine Sensor Open/Short Test
2003/09/01 New Slave Piston Lash Settings are Available for Heavy-Duty Diesel Engines {1119, 1129}
Cold Weather Recommendations for On-Highway Diesel Truck Engines Cold Weather Recommendation Charts
Installation Guide for Industrial Electronic Engine Displays Wiring - J1939 Data Link