GSC CID 0590 - FMI 09
产生此代码的情况:
该故障代码通常与 EUI 应用程序有关。 CID 0590 故障表示:为响应 GSC+ 信息的定期请求,已停用了发动机电子控制模块。
注: 该诊断代码可能会在 MUI 应用程序上出现。 该诊断代码是由 P023 设定点编程错误造成的。 对于 MUI 应用程序,GSC+的设定点 P023 必须设为 0。 重新编程该设定点及其他 GSC+ 设定点。 请参阅系统操作, "发动机/发电机编程 OP5-0"。
测试步骤 1. 检查 CAT 数据链路
- 将 ECS 转到断开 / 复位位置。
- 从 GSC+ 上断开 CAT 数据链路的触点 19 和 20。
- 从 ECM 上断开 CAT 数据链路的触点 13 和 14。
- 测量 GSC+ 的触点 19 和 ECM 的触点 14 之间的电阻。
- 测量 GSC+ 的触点 20 和 ECM 的触点 13 之间的电阻。
预期结果:
两个电阻测量值都小于 5 欧姆。
结果:
- 正常 - 两个电阻测量值都小于 5 欧姆。 电路正常。 ECM 出现故障。
修复: ECM 不太可能会出现故障。 更换 ECM 之前,请先参阅故障排除, SENR1003, "3500B EPG 发动机"或故障排除, RENR2227, "3406E EPG 发动机"。故障排除后清除故障日志中的诊断代码。 通常编程 GSC+ 以将 CID 590 诊断代码作为"报警故障"处理。 设定点 P04 为 0。 如果编程 GSC 以将该代码作为停机故障处理,则设定点 P04 为 1。 此时查看该诊断代码无需按下"报警代码"键。 上显示屏上自动显示该诊断代码。
停止
- 异常 - 两个电阻测量值都大于 5 欧姆。 电路不正常。
修复: 维修 CAT 数据链路的接线,或更换 CAT 数据链路的接线。故障排除后清除故障日志中的诊断代码。 通常编程 GSC+ 以将 CID 590 诊断代码作为"报警故障"处理。 设定点 P04 为 0。 如果编程 GSC 以将该代码作为停机故障处理,则设定点 P04 为 1。 此时查看该诊断代码无需按下"报警代码"键。 上显示屏上自动显示该诊断代码。
停止
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1168 - FMI 03
G3406 Engine Engine Oil Sample - Obtain
G3516B Engines Electrical Power Supply
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1167 - FMI 04
G3406 and G3412 Generator Sets Engine Oil and Filter - Change
G3406 and G3412 Generator Sets Engine Oil Level - Check
G3300 Engines Exhaust Bypass - Inspect
G3408C and G3412C Engines Cooling System Coolant (DEAC) - Change
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Disassemble
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1038 - FMI 04
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application Programmable Parameters
3500B Engines for Caterpillar Built Power Modules Magnetic Switch
PM3412C Power Modules Setup
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Assemble
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0168 - FMI 03
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0441 - FMI 12 (for MUI Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1168 - FMI 04
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0441 - FMI 12 (for PEEC Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0770 - FMI 09 (for EUI and PEEC Engines)
G3516B Engines Ignition Transformers Primary Circuit
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0442 - FMI 12
G3406 Engine Engine Oil Level - Check
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0770 - FMI 09 (for MUI Engines)
3500B Engines for Caterpillar Built Power Modules with the ADEM 2 Electronic Control Module Electrical Connectors and Functions