Water Pump - Disassemble
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 5F-7344 | 拉拔器板(1) | 1 |
5F-7345 | 螺钉(1) | 1 | |
7S-7789 | 保险杠(1) | 2 | |
B | 1P-1861 | 挡圈钳 | 1 |
C | 8B-7554 | 拉拔器总成 | 1 |
Show/hide table
(1) | 8B-7554 轴承外圈拉拔器 的一部分 |
开始:
- 拆下水泵。 请参阅 拆解和组装, "水泵 - 拆卸" 。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
图 1 | g01020687 |
- 拆除将水泵与散热器相连的弯头组件。 拆除将水泵与机油冷却器相连的弯头组件。
- 拆下盖螺栓 (3) 。 将壳体 (9) 从盖上小心地分离。
- 固定住六角垫圈 ( 1)。 拆下内六角头螺栓 ( 4)。
- 拆下轴承 (5)。
- 使用工具 (A),卸下齿轮 ( 6)。
- 使用工具 (B) 拆下挡圈 ( 7)。
- 利用工具 (C) 拆下叶轮 ( 11)。
- 利用适当的压具拆除内轴承 ( 5) 和轴组件 (8)。
- 拆下水封 (10)。
- 拆下油封 (2)。
Caterpillar Information System:
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1038 - FMI 04
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application Programmable Parameters
3500B Engines for Caterpillar Built Power Modules Magnetic Switch
37-MT, 41-MT, and 42-MT Series Starting Motors Normal Operation
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0441 - FMI 12 (for EUI Engines)
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1038 - FMI 03
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application General Information
Electronic Modular Control Panel II+ (EMCP II+) Indicator for Overcrank (for PEEC Engines)
37-MT, 41-MT, and 42-MT Series Starting Motors Component Description
37-MT, 41-MT, and 42-MT Series Starting Motors Service Tools
PM3412C Power Modules Equipment Parking
G3516B Engines Detonation Sensors
G3408C and G3412C Engines Cooling System Coolant (DEAC) - Change
G3300 Engines Exhaust Bypass - Inspect
G3406 and G3412 Generator Sets Engine Oil Level - Check
G3406 and G3412 Generator Sets Engine Oil and Filter - Change
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1167 - FMI 04
G3516B Engines Electrical Power Supply
G3406 Engine Engine Oil Sample - Obtain
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 1168 - FMI 03
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0590 - FMI 09
PM3412C Power Modules Setup
3176C and 3196 Engines For Caterpillar Built Machines Water Pump - Assemble
Electronic Modular Control Panel II+ (EMCP II+) GSC CID 0168 - FMI 03