Rear Suspension Frame - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8S-9906 | Ratchet Hoist | 2 |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 1 g00577059 - Use pin (6) and a hammer, or use a press in order to install bearing (13).
Show/hide table
Illustration 2 g00575865 - Place clamp ring (12) into position. Install six bolts (11).
Show/hide table
Illustration 3 g00575861 Show/hide tableIllustration 4 g00575862 Show/hide tableIllustration 5 g00575860 - Position the center suspension frame under the machine. Attach Tooling (A) and appropriate nylon lifting slings to each side of the rear of center suspension frame (1).
- Place the front of the center suspension frame on an appropriate floor jack.
- Use Tooling (A) and the floor jack in order to raise the frame to the machine. The weight of frame (1) is
187 kg (412 lb) .Show/hide tableIllustration 6 g00577311 - Install six bolts (10) to housing (9).
Note: It may be necessary to leave the bolts loose until the frame is connected at each point.
Show/hide tableIllustration 7 g00575863 - Use three people or an appropriate lifting device in order to position bracket (8) to the machine. The weight of the bracket is
40 kg (88 lb) . Install six bolts (7) and the washers that secure the bracket to housing (9).Note: It may be necessary to leave the bolts loose until the frame is connected at each point.
Show/hide tableIllustration 8 g00577422 - Lubricate pin (6). Install the pin. Use a suitable driver in order to install the pin.
Show/hide table
Illustration 9 g00577312 Note: Apply 9S-3263 Thread Lock Compound to the threads of bolt (5).
- Install bolt (5), the washer, washer (3), nut (4), and the washer.
- Connect grease line (2) to washer (3).
- Remove Tooling (A) and the floor jack from the machine.
- Lubricate pin (6). Use the grease fitting on the bulkhead adapter. The fitting is located at the front of the rear frame. Refer to Operation and Maintenance Manual, SEBU7064 for the proper procedure.
End By:
- Install the rear axle stabilizer rod. Refer to Disassembly and Assembly, "Rear Axle Stabilizer Rod - Remove and Install".
Caterpillar Information System:
D350E Series II Articulated Truck Center Suspension Frame - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System CID 060 FMI F00 Electrical System Voltage Value Too High - Test
793C Off-Highway Truck Power Train Oil Filter and Base (Torque Converter) - Install
D350E Series II Articulated Truck Accumulator (Suspension) - Remove and Install
D350E Series II Articulated Truck Fender - Remove and Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Speed Sensor - Adjust
D350E Series II Articulated Truck Parking Brake - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Glossary of Electrical Terms
D350E Series II Articulated Truck Service Brake - Install
D350E Series II Articulated Truck Service Brake - Assemble
D350E Series II Articulated Truck Service Brake - Disassemble
D350E Series II Articulated Truck Pressure Reducing Valve (Hoist Pilot Pressure) - Remove and Install
65E, 75E, 85E and 95E Agricultural Tractors Hydraulic Oil Filter (Return) and Base - Remove and Install
D350E Series II Articulated Truck Front Frame and Rear Frame - Separate
65E, 75E, 85E and 95E Agricultural Tractors Steering Oil Filter and Base - Remove and Install
D350E Series II Articulated Truck Oscillating Hitch - Remove
D350E Series II Articulated Truck Oscillating Hitch - Install
793C Off-Highway Truck Power Train Screen (Torque Converter) - Remove
D350E Series II Articulated Truck Fuel Tank - Install
789C Off-Highway Truck Machine Systems Center Arm (Steering) - Remove and Install
789C Off-Highway Truck Machine Systems Steering Arm - Remove and Install
793C Off-Highway Truck Power Train Oil Filter and Base (Rear Axle) - Remove
TH103 Telehandler Hydraulic Tank Breather - Clean
D350E Series II Articulated Truck Front Suspension Cylinder - Install