Service Brake - Install
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Lubricate O-ring seals with an appropriate lubricant.
- Install the O-ring to the spindle.
Show/hide table
Illustration 1 g00584491 Show/hide tableIllustration 2 g00584490 Show/hide tableIllustration 3 g00584489 - Place brake housing (5) on a hydraulic table, or a lifting device.
- Position the brake housing assembly to the machine. The weight of the assembly is
275 kg (606 lb) . Install 26 bolts (6) and the washers that secure brake housing (5) to axle housing (7). Tighten the bolts to a torque of430 ± 60 N·m (317 ± 44 lb ft) . - Install the O-ring to hose assembly (4). Connect the hose assembly.
- Install the two O-rings to hose assemblies (3). Install the eight bolts, the washers, and the four half clamps that secure the hose assemblies.
Show/hide table
Illustration 4 g00584502 - Position cover (2) to the machine. Install three bolts (1) and the washers that secure the cover.
- Check and fill the level of the oil. Refer to Operation and Maintenance Manual, SEBU7064, "Hoist, Steering, and Brake System Oil Level - Check" for the proper procedure.
- Engage the parking brake. Place the gear selector in the neutral position. Start the engine and pump the brakes. Check for a hard pedal. Check the brake lines for leaks.
End By:
- Install the wheel. Refer to Disassembly and Assembly, "Wheel - Install".
Caterpillar Information System:
D350E Series II Articulated Truck Service Brake - Assemble
D350E Series II Articulated Truck Service Brake - Disassemble
D350E Series II Articulated Truck Pressure Reducing Valve (Hoist Pilot Pressure) - Remove and Install
TH103 Telehandler Maintenance Interval Schedule
D350E Series II Articulated Truck Hoist Control Valve - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System System Schematic
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System CID 058 FMI F06 Solenoid Valve (Rotor Clutch) Current Above Normal - Test
D350E Series II Articulated Truck Hoist Control Valve - Assemble
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System CID 058 FMI F05 Solenoid Valve (Rotor Clutch) Current Below Normal - Test
3126B Engines for Caterpillar Built Machines Camshaft Gear - Remove and Install
D350E Series II Articulated Truck Steering Cylinder - Install
D350E Series II Articulated Truck Steering Check and Combiner Valve - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Glossary of Electrical Terms
D350E Series II Articulated Truck Parking Brake - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Speed Sensor - Adjust
D350E Series II Articulated Truck Fender - Remove and Install
D350E Series II Articulated Truck Accumulator (Suspension) - Remove and Install
793C Off-Highway Truck Power Train Oil Filter and Base (Torque Converter) - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System CID 060 FMI F00 Electrical System Voltage Value Too High - Test
D350E Series II Articulated Truck Center Suspension Frame - Install
D350E Series II Articulated Truck Rear Suspension Frame - Install
65E, 75E, 85E and 95E Agricultural Tractors Hydraulic Oil Filter (Return) and Base - Remove and Install
D350E Series II Articulated Truck Front Frame and Rear Frame - Separate
65E, 75E, 85E and 95E Agricultural Tractors Steering Oil Filter and Base - Remove and Install