Oscillating Hitch - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 5P-9694 | Ratchet Hoist | 2 |
B | 138-7573 | Link bracket | 1 |
- Inspect all parts and clean all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
Show/hide table
Illustration 1 g00582767 - Apply 3S-6252 Sealant as a
3 mm (0.12 inch) radial bead at reference point (14) to the contact surface of wear plate (13) only. Apply 3S-6252 Sealant as a5 mm (0.2 inch) radial bead at reference point (15) to the contact surface of wear plate (13) only.Show/hide tableIllustration 2 g00579673 - Immediately position wear plate (13) on oscillating hitch (1). Install two bolts (12) and the dowels on wear plate (13).
Show/hide table
Illustration 3 g00584790 - Apply 4C-9500 Quick Cure Primer to the outside diameter of two bushings (11). Allow the bushings to dry for three minutes.
- Apply 4C-4032 Bearing Mount Compound over area (X) on the outside diameters of bushings (11). Assemble bushings (11) into the frame within five to ten minutes of the application.
Show/hide table
Illustration 4 g00580298 - Install seal (10) on rear frame (9). The seal and the inside diameter of bushings (11) should be packed with 7X-7699 Lubricating Grease prior to the installation of the hitch assembly.
Show/hide table
Illustration 5 g00580307 - Attach the suitable lifting straps and a hoist to oscillating hitch (1). Use Tooling (A), the hoist and a block in order to level oscillating hitch (1) on the hoist. Apply 7X-7699 Lubricating Grease to the tube of oscillating hitch (1). Slowly install oscillating hitch (1) to rear frame (9).
Show/hide table
Illustration 6 g00580264 - Attach Tooling (B) and Tooling (A) to drive shaft yoke assembly (3), as shown. Use two persons in order to install drive shaft yoke assembly (3) and the shaft (not shown) to housing (5).
Show/hide table
Illustration 7 g00586364 - Use a large punch in order to assist in the installation of drive shaft yoke assembly (3).
Show/hide table
Illustration 8 g00580253 - Install nine nuts (6) and the washers that secure drive shaft yoke assembly (3) to housing (5).
Show/hide table
Illustration 9 g00580249 - Use a ratchet wrench and locking plate assembly (2) in order to install thrust flange (4) to drive shaft yoke assembly (3). Use the ratchet to rotate thrust flange (4) until the assembly is tight. Then use the ratchet to back off thrust flange (4) one notch. Secure locking plate assembly (2) to drive shaft yoke assembly (3).
Show/hide table
Illustration 10 g00579684 - Install oscillating hitch (1) to the machine. Remove the lifting straps and the hoist.
End By:
- Install the parking brake. See Disassembly and Assembly, "Parking Brake - Remove and Install".
- Connect the front and the rear frames. See Disassembly and Assembly, "Front and Rear Frame - Seperate and Connect".
Caterpillar Information System:
D350E Series II Articulated Truck Oscillating Hitch - Remove
65E, 75E, 85E and 95E Agricultural Tractors Steering Oil Filter and Base - Remove and Install
D350E Series II Articulated Truck Front Frame and Rear Frame - Separate
65E, 75E, 85E and 95E Agricultural Tractors Hydraulic Oil Filter (Return) and Base - Remove and Install
D350E Series II Articulated Truck Rear Suspension Frame - Install
D350E Series II Articulated Truck Center Suspension Frame - Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System CID 060 FMI F00 Electrical System Voltage Value Too High - Test
793C Off-Highway Truck Power Train Oil Filter and Base (Torque Converter) - Install
D350E Series II Articulated Truck Accumulator (Suspension) - Remove and Install
D350E Series II Articulated Truck Fender - Remove and Install
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Speed Sensor - Adjust
D350E Series II Articulated Truck Parking Brake - Install
793C Off-Highway Truck Power Train Screen (Torque Converter) - Remove
D350E Series II Articulated Truck Fuel Tank - Install
789C Off-Highway Truck Machine Systems Center Arm (Steering) - Remove and Install
789C Off-Highway Truck Machine Systems Steering Arm - Remove and Install
793C Off-Highway Truck Power Train Oil Filter and Base (Rear Axle) - Remove
TH103 Telehandler Hydraulic Tank Breather - Clean
D350E Series II Articulated Truck Front Suspension Cylinder - Install
793C Off-Highway Truck Power Train Oil Filter and Base (Rear Axle) - Install
793C Off-Highway Truck Power Train Oil Filter and Base (Rear Axle) - Disassemble
793C Off-Highway Truck Power Train Oil Filter and Base (Rear Axle) - Assemble
RM-350 and SM-350 Road Reclaimer/Soil Stabilizers Machine Electronic Control System Calibration
3126B Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove