Idler - Disassemble
Disassembly Procedure
Start By:
- Remove the idlers. Refer to Disassembly and Assembly, "Idler - Remove" for the correct procedure.
- Use a slow drill and a 12.7 mm (0.50 inch) drill bit to remove plug (4) and stopper (3) from the end of the shaft.
Show/hide table
Illustration 1 | g00616829 |
- Remove the washers, eight bolts (2), and retainer (1) from each side of the idler.
Note: The shaft will be able to fall when the retainers are removed.
- Remove O-ring seal (6) from retainer (1) .
Show/hide table
Illustration 2 | g00616832 |
- Put identification marks on Duo-cone seal (5). Remove Duo-cone seal (5) from retainer (1) .
Note: If the Duo-cone seals will be reused, put identification marks on the seals. This will allow the seals to be assembled and installed in the original position.
- Put identification marks on Duo-cone seal (7). Remove Duo-cone seal (7) and toric stabilizer (9) from each side of shaft (8) .
Show/hide table
Illustration 3 | g00616833 |
- Remove washer (10) from both ends of shaft (8) .
Show/hide table
Illustration 4 | g00616843 |
- Pull shaft (8) out of the idler so that the hoist can be fastened to the shaft.
Show/hide table
Illustration 5 | g00616846 |
- Fasten a hoist to shaft (8). Remove the shaft from idler assembly (11). The weight of the shaft is 21 kg (46.3 lb).
Caterpillar Information System:
517 Track-Type Skidder Engine Supplement Hood - Remove and Install
517 Track-Type Skidder Engine Supplement Fuel Transfer Pump - Install
517 Track-Type Skidder Engine Supplement Fuel Transfer Pump - Assemble
517 Track-Type Skidder Engine Supplement Fuel Transfer Pump - Disassemble
517 Track-Type Skidder Engine Supplement Fuel Transfer Pump - Remove
517 Track-Type Skidder Engine Supplement Fuel Priming Pump - Remove and Install
784C and 785C Off-Highway Trucks Machine Systems Steering Accumulator - Remove
D250E Series II and D300E Series II Articulated Trucks Power Train Transmission Hydraulic Control Valve - Remove
3500B and 3500B High Displacement Generator Set Engines Oil Contains Coolant
3524B Engines for Off-Highway Trucks Fuel in Cooling System
69D and 769D Off-Highway Trucks and 771D Quarry Truck Power Train Pressure Switch (Service Brake and Retarder)
69D and 769D Off-Highway Trucks and 771D Quarry Truck Power Train Pressure Switch (Secondary Brake and Parking Brake)
517 Track-Type Skidder Engine Supplement Muffler and Exhaust Extension - Remove and Install
572R Pipelayer Power Train Idler - Assemble
3524B Engines for Off-Highway Trucks Low Engine Oil Pressure
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) Charging System - Test
793C Off-Highway Truck/Tractor Power Train Lockup Clutch and Synchronizing Valve - Disassemble
572R Pipelayer Power Train Steering Clutch and Brake - Disassemble
3524B Engines for Off-Highway Trucks Coolant Temperature Is Too High
517 Track-Type Skidder Engine Supplement Radiator Guard - Remove
517 Track-Type Skidder Engine Supplement Radiator - Remove
517 Track-Type Skidder Engine Supplement Radiator - Disassemble
517 Track-Type Skidder Engine Supplement Radiator - Assemble
517 Track-Type Skidder Engine Supplement Radiator - Install