Lateral Control Rod (Rear Axle Housing) - Assemble
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
1 | 1U-8758 | Retaining Ring Pliers | 1 |
1 | 1P-0520 | Driver Group | 1 |
- Use Tool (A) to install retaining ring (3).
- Turn the lateral control rod (rear axle housing).
Show/hide table
Illustration 2 g00517498 Show/hide tableIllustration 3 g00517500 - Use Tool (B) and a suitable press to assemble bearing (4) into the bore until the bearing is seated against retaining ring (3).
Note: During the installation of bearing (4), lower the temperature of the bearing to
−50 °C (−58.0 °F) .Note: A band retains the bearing race. The bearing race is split into two parts. After the bearing is installed by approximately one-third of the final depth, remove the band. Finish the installation of the bearing.
- Turn the lateral control rod (rear axle housing). Use Tool (A) to install retaining ring (2).
- Repeat Steps 1 through 4 for the bearing that is at the opposite end of the lateral control rod (rear axle housing).
Show/hide table
Illustration 1 | g00517497 |
End By:
- Install the lateral control rod (rear axle housing). Refer to Disassembly and Assembly, "Lateral Control Rod (Rear Axle Housing) - Install".
Caterpillar Information System:
517 Track-Type Skidder Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
517 Track-Type Skidder Engine Supplement Fan Drive - Assemble
517 Track-Type Skidder Engine Supplement Fan Drive - Disassemble
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Service and Parking Brake (Rear)
517 Track-Type Skidder Engine Supplement Engine Oil Filter and Base - Install
517 Track-Type Skidder Engine Supplement Engine Oil Filter Base - Disassemble
517 Track-Type Skidder Engine Supplement Engine Oil Filter Base - Assemble
517 Track-Type Skidder Engine Supplement Engine Oil Filter and Base - Remove
517 Track-Type Skidder Engine Supplement Engine and Torque Converter - Remove
517 Track-Type Skidder Engine Supplement Engine and Torque Converter - Install
517 Track-Type Skidder Engine Supplement Electric Starting Motor - Remove and Install
517 Track-Type Skidder Engine Supplement Alternator - Remove and Install
554 Forwarder and 574 Forwarder Stopping the Machine
TK711, TK721, TK722 and TK732 Track Feller Bunchers Machine Systems Swing Drive - Disassemble
C-9 Engine for TK711, TK721, TK722, TK732, TK741, TK751, and TK752 Track Feller Bunchers Engine Oil in Cooling System
793C and 793C XQ Off-Highway Trucks Hydraulic System Relief Valve (Brake Oil Cooler) - Test and Adjust
980G Wheel Loader Power Train Axle Shaft - Remove and Install
824G , 825G and 826G Landfill Compactor Cleaner Bar Tips - Replace
784C and 785C Off-Highway Trucks Machine Systems Window Wiper Motor - Remove and Install
3176C and 3196 Industrial Engines Engine Oil Pressure Sensor - Remove and Install
3176C and 3196 Industrial Engines Speed/Timing Sensor - Remove and Install
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Temperature Sensor (Brake Oil)
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Engine Front Support - Install
69D and 769D Off-Highway Trucks and 771D Quarry Truck Power Train Pressure Switch (Secondary Brake and Parking Brake)