Electric Starting Motor - Remove and Install
Removal Procedure
Show/hide table
Illustration 1 | g00555279 |
- Remove two bolts (2) from access door (1). Open the door for access to the batteries.
- Disconnect battery cables (3) from batteries (4) .
Show/hide table
Illustration 2 | g00555283 |
- Remove six bolts (6) from engine access panel (5) on the right side of the machine (lower panel). Remove the panel.
Show/hide table
Illustration 3 | g00555286 |
- Put identification marks on the four wires that are connected to terminal (9) and the two wires that are connected to terminal (7). Disconnect the wires from starter (8) .
Show/hide table
Illustration 4 | g00555289 |
- Remove cover (10). Put identification marks on the two wires on the terminal under the cover. Disconnect the two wires from the terminal.
- Remove three bolts (11). Use two people to remove the starter. The weight of the starter is 27 kg (60 lb).
Show/hide table
Illustration 5 | g00555291 |
Installation Procedure
Show/hide table
Illustration 6 | g00555291 |
Note: Check the condition of the gasket that was removed with the starter. Install a new gasket, if necessary.
- Use two people to place starter (8) in position. The weight of the starter is 27 kg (60 lb). Install three bolts (11) .
- Connect two wires to the terminal that is located under cover (10). Install cover (10) .
Show/hide table
Illustration 7 | g00555289 |
- Connect two wires to terminal (7). Connect four wires to terminal (9) .
- Place engine access panel (5) in position and install six bolts (6) .
Show/hide table
Illustration 8 | g00555286 |
- Connect battery cables (3) to battery (4) .
Show/hide table
Illustration 9 | g00555283 |
- Close access door (1) and install two bolts (2) .
Show/hide table
Illustration 10 | g00555279 |
Caterpillar Information System:
517 Track-Type Skidder Engine Supplement Alternator - Remove and Install
517 Track-Type Skidder Engine Supplement Air Cleaner - Remove and Install
Caterpillar Monitoring System Charge Pressure Display Mode
69D and 769D Off-Highway Trucks and 771D Quarry Truck Power Train Transmission Gear Indicator
3412E Engine Supplement for 773D Off-Highway Trucks and 775D Off-Highway Quarry Trucks Engine Front Support - Remove
784C and 785C Off-Highway Trucks Machine Systems Cab - Install
3406E On-Highway Engine Engine Oil Pressure Sensor - Remove and Install
Caterpillar Monitoring System Engine Oil Pressure Display Mode
527 Track-Type Skidder Power Train Testing and Adjusting
D250E Series II and D300E Series II Articulated Trucks Machine Systems Center Axle Stabilizer Rod - Remove and Install
3406E On-Highway Engine Coolant Temperature Sensor - Remove and Install
416C, 426C, 428C, 436C and 438C Backhoe Loaders Hydraulic and Steering System Stabilizer Cylinders
517 Track-Type Skidder Engine Supplement Engine and Torque Converter - Install
517 Track-Type Skidder Engine Supplement Engine and Torque Converter - Remove
517 Track-Type Skidder Engine Supplement Engine Oil Filter and Base - Remove
517 Track-Type Skidder Engine Supplement Engine Oil Filter Base - Assemble
517 Track-Type Skidder Engine Supplement Engine Oil Filter Base - Disassemble
517 Track-Type Skidder Engine Supplement Engine Oil Filter and Base - Install
69D and 769D Off-Highway Truck and 771D Quarry Truck Air System and Brakes Service and Parking Brake (Rear)
517 Track-Type Skidder Engine Supplement Fan Drive - Disassemble
517 Track-Type Skidder Engine Supplement Fan Drive - Assemble
517 Track-Type Skidder Engine Supplement Fuel Filter (Primary) and Fuel Filter Base - Remove and Install
793C Off-Highway Truck/Tractor Power Train Lateral Control Rod (Rear Axle Housing) - Assemble
554 Forwarder and 574 Forwarder Stopping the Machine