Transfer Gearbox - Remove
- 拆下防护罩组件 (1)。
Show/hide table
图 2 g03264084 - 拆下线束组件 (2)。 拆下软管组件 (4)。 将线束组件 (3) 安置在旁边。
Show/hide table
图 3 g03261793 - 拆下软管组件 (5)。
Show/hide table
图 4 g03262997 - 拆下螺栓 (6)。 拆下定位螺钉 (7)。 对另一侧重复上述步骤。
Show/hide table
图 5 g03263038 - 拆下螺栓 (8) 和 (9)。 对另一侧重复上述步骤。
Show/hide table
图 6 g03263117 注: 断开任何必要的加感电缆或导线,以便正确移动发电机组件 (10)。
- 使用合适的起吊设备,将发电机组件 (10) 从后内连接器 (11) 上滑开大约
305 mm (12 in) 。 发电机组件 (10 )的重量约为4082 kg (9000 lb) 。 - 使用合适的起吊设备或由两个人拆下后内连接器 (11)。 后内连接器 (11) 的重量约为
31 kg (68 lb) 。Show/hide table图 7 g03263237 - 拆下螺栓 (12)。 拆下调整螺钉 (13)。 对另一侧重复上述步骤。
Show/hide table
图 8 g03263279 - 使用合适的起吊设备,滑动分动箱组件 (14),直到可以拆下前内连接器 (15)。 分动箱组件 (14) 的重量约为
1193 kg (2630 lb) 。 使用合适的起吊设备或由两个人拆下前内连接器 (15)。 前内连接器 (15) 的重量约为31 kg (68 lb) 。Show/hide table图 9 g03263378 - 使用合适的起吊设备拆下分动箱组件 (14)。 分动箱组件 (14) 的重量约为
1193 kg (2630 lb) 。
Show/hide table
图 1 | g03261785 |
Caterpillar Information System:
C2.6 and C3.3B Engines for Caterpillar Built Machines Electric Starting Motor
C2.6 and C3.3B Engines for Caterpillar Built Machines Alternator and Regulator
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562} Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
C1.5 and C2.2 Industrial Engines Multiposition Switch Setup
C175-16 Engine Turbocharger Turbine Temperature Is High
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Normal Operation
C175-16 Engine Prelubrication Pump Problem
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 0674 - FMI 08
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Operator Control Switch (Switch to Ground) - Test
C175-16 Engine Oil Temperature Is High
C175-16 Engine Oil Pressure Is Low
C175-16 Engine Oil Filter Differential Pressure Problem
G3512H and G3516H Generator Set Engines Transfer Gearbox - Install
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Engagement Pressure for the Transmission Clutch - Calibrate
Installation Procedure for Product LinkTM PLE640 Systems{7606} Installation Procedure for Product LinkTM PLE640 Systems{7606}
C18 Marine Engine Crankshaft Vibration Damper - Inspect
C18 Marine Engine Plate Locations and Film Locations
Alternator - Bosch K1/N1 General Information
Alternator - Bosch K1/N1 Service Tools
C1.5 and C2.2 Industrial Engines Customer Specified Parameters
Alternator - Bosch K1/N1 Diode Assembly - Test
C1.5 and C2.2 Engines for Caterpillar Built Machines System Configuration Parameters
C1.5 and C2.2 Engines for Caterpillar Built Machines Replacing the ECM
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Oil Level - Test