Transfer Gearbox - Install
- 使用合适的起吊设备定位分动箱组件 (14),如图所示。
Show/hide table
图 2 g03263279 - 使用合适的起吊设备或由两个人安装前内连接器 (15)。 前内连接器 (15) 的重量约为
31 kg (68 lb) 。 使用合适的起吊设备将分动箱组件 (14) 滑动到位。 分动箱组件 (14) 的重量约为1193 kg (2630 lb) 。Show/hide table图 3 g03263237 - 安装螺栓 (12)。 安装调整螺钉 (13)。
Show/hide table
图 4 g03263117 - 使用合适的起吊设备或由两个人安装后内连接器 (11)。 后内连接器 (11) 的重量约为
31 kg (68 lb) 。 使用合适的起吊设备,朝向后内连接器 (11) 滑动发电机组件 (10)。 发电机组件 (10 )的重量约为4082 kg (9000 lb) 。Show/hide table图 5 g03262997 - 安装螺栓 (6)。 安装定位螺钉 (7)。
Show/hide table
图 6 g03261793 - 安装软管组件 (5)。
Show/hide table
图 7 g03264084 - 重新定位线束组件 (3)。 安装线束组件 (2)。 安装软管组件 (4)。
Show/hide table
图 8 g03261785 - 安装防护罩组件 (1)。
Show/hide table
图 1 | g03263378 |
Caterpillar Information System:
G3512H and G3516H Generator Set Engines Transfer Gearbox - Remove
C2.6 and C3.3B Engines for Caterpillar Built Machines Electric Starting Motor
C2.6 and C3.3B Engines for Caterpillar Built Machines Alternator and Regulator
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562} Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
C1.5 and C2.2 Industrial Engines Multiposition Switch Setup
C175-16 Engine Turbocharger Turbine Temperature Is High
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Normal Operation
C175-16 Engine Prelubrication Pump Problem
793F and 797F Off-Highway Trucks Power Train Electronic Control System MID 081 - CID 0674 - FMI 08
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Operator Control Switch (Switch to Ground) - Test
C175-16 Engine Oil Temperature Is High
C175-16 Engine Oil Pressure Is Low
CX48-P2300 Petroleum Transmission Power Train Electronic Control System Engagement Pressure for the Transmission Clutch - Calibrate
Installation Procedure for Product LinkTM PLE640 Systems{7606} Installation Procedure for Product LinkTM PLE640 Systems{7606}
C18 Marine Engine Crankshaft Vibration Damper - Inspect
C18 Marine Engine Plate Locations and Film Locations
Alternator - Bosch K1/N1 General Information
Alternator - Bosch K1/N1 Service Tools
C1.5 and C2.2 Industrial Engines Customer Specified Parameters
Alternator - Bosch K1/N1 Diode Assembly - Test
C1.5 and C2.2 Engines for Caterpillar Built Machines System Configuration Parameters
C1.5 and C2.2 Engines for Caterpillar Built Machines Replacing the ECM
3516B and 3516C Engines For MT4400D AC Off-Highway Trucks Oil Level - Test
C18 Marine Engine Coolant Level - Check