Fuel Injection Pump
Show/hide table
 | |
| 图 1 | g03662748 |
Show/hide table
| 359-5546 喷油泵总成 的技术规格 | |||
| 项目 | 数量 | 零件 | 技术规格说明 |
| 1 | 8 | 3T-0849 螺栓 | 按照以下步骤拧紧螺栓： 1. 按图 1 中所示的数字顺序将螺栓拧紧至 6 N·m (53 lb in)。 2. 再次按照数字顺序将螺栓拧紧至 12 N·m (106 lb in)。 3. 确保所有螺栓拧紧至 12 N·m (106 lb in)。 |
| 2 | 12 | 177-1809 螺栓 | 按照以下步骤拧紧螺栓： 1. 按图 1 中所示的数字顺序将螺栓拧紧至 18 N·m (13 lb ft)。 2. 再次按照数字顺序将螺栓拧紧至 36 N·m (27 lb ft)。 3. 确保所有螺栓拧紧至 36 N·m (27 lb ft)。 |
| 3 | 4 | 8T-4178 螺栓 | 按照以下步骤拧紧螺栓： 1. 按图 1 中所示的数字顺序将螺栓拧紧至 20 N·m (15 lb ft)。 2. 再次按照数字顺序将螺栓拧紧至 40 N·m (30 lb ft)。 3. 最后，按照数字顺序将螺栓拧紧至 60 N·m (44 lb ft)。 |
| 4 | 1 | 241-6157 螺塞 | 拧紧至扭矩为 23 ± 3 N·m (204 ± 27 lb in)。 |
Caterpillar Information System:
C18 Generator Set Plate Locations and Film Locations
C15 and C18 Engines for Caterpillar Built Machines Boost Pressure Sensor - Remove and Install
EMCP4.1/EMCP4.2 Output Programming
349F and 352F Excavators Camera Harness - Disconnect and Connect
2010/06/25 A New Water Connection Gp Is Used on C32 Engines that Are Keel Cooled {1380}
C15 and C18 Industrial Engines Engine Control Module - Remove and Install
C27 Generator Set Engines Vibration Damper and Pulley
C13 Engine for Combat and Tactical Vehicles Main Bearing Journal
C9.3 Tier 4 Interim Engines Speed Control (PTO) - Test
C4.4 Industrial Engine Engine Operation
CX35-P800 Petroleum Transmission Maintenance Interval Schedule
CB22B, CB24B, CB32B and CC24B Utility Compactors Film (Product Identification) - Clean
G3516C and G3516E Gas Engines Jacket Water Heater
2010/02/19 A New Tool is Available to Test and Adjust the Setting of the Main Relief Valve and the Line Relief Valves for Certain Excavators {0784, 5051, 5069, 5117}
C18 Generator Set Generator Start-up Checklist
3508C, 3512C and 3516C Marine Engines Heat Exchanger - Disassemble
C18 Generator Set Generator Bearing - Lubricate
C15 and C18 Industrial Engines Fuel Temperature Sensor - Remove and Install
C18 Generator Set Product Installation
C15 and C18 Industrial Engines Fuel Pressure Sensor - Remove and Install
C15 and C18 Industrial Engines Coolant Temperature Sensor - Remove and Install
3508C, 3512C and 3516C Marine Engines Heat Exchanger - Assemble
3508C, 3512C and 3516C Marine Engines Heat Exchanger - Assemble
C15 and C18 Engines Product Description