Piston and Rings - Three Ring Piston
Show/hide table
图 1 | g01038789 |
(1) 安装顶环时必须使黄色条朝向活塞环开口间隙右侧。 安装顶环时必须使 "UP-1" 朝上。 活塞环开口间隙必须与相邻活塞环开口间隙隔 120 ± 20 度。
(2) 安装第二道活塞环时必须使绿色条朝向活塞环开口间隙右侧。 安装中间环时必须使 "UP-2" 朝上。 活塞环开口间隙必须与相邻活塞环开口间隙隔 120 ± 20 度。
(3) 安装油控环和油环弹簧,使各环的开口相隔 180 度。 从油控环开口间隙中必须能够看见油环弹簧的白色部分。 活塞环开口间隙必须与相邻活塞环开口间隙隔 120 ± 20 度。
注: 表 1 为新活塞的技术规范。
Show/hide table
活塞和活塞环     | ||||
项目 | (1) 顶环     | (2) 第二道环     | (3) 油控环     | |
新活塞的槽宽     | 6.185 ± 0.015 mm (0.2435 ± 0.0006 in)     |
6.155 ± 0.015 mm (0.24232 ± 0.00059 in)     |
8.050 ± 0.010 mm (0.3169 ± 0.0004 in)     |
|
活塞环的宽度     | 5.9825 ± 0.0075 mm (0.2355 ± 0.0003 in)     |
5.9825 ± 0.0075 mm (0.2355 ± 0.0003 in)     |
7.976 ± 0.011 mm (0.3140 ± 0.0004 in)     |
|
环槽和活塞环之间的间隙     | 0.2025 ± 0.0225 mm (0.0080 ± 0.0009 in)     |
0.1725 ± 0.0225 mm (0.0068 ± 0.0009 in)     |
0.074 ± 0.021 mm (0.0029 ± 0.0008 in)     |
|
活塞环开口间隙 (1)     |
1.15 ± 0.15 mm (0.0453 ± 0.0059 in)     |
1.95 ± 0.15 mm (0.0768 ± 0.0059 in)     |
1.1 ± 0.20 mm (0.043 ± 0.008 in)     |
Show/hide table
( 1 ) | 给出的值适用于安装在孔 280 mm (11.024 in) 中的活塞环。 |
活塞销孔 ... 120.025 ± 0.010 mm (4.7254 ± 0.0004 in)
活塞销直径 ... 119.994 ± 0.006 mm (4.7242 ± 0.0002 in)
活塞销和活塞孔之间冷态间隙 ... 0.031 ± 0.016 mm (0.0012 ± 0.0006 in)
Caterpillar Information System:
2008/10/27 Replace the Two-Piece Piston if the Piston Contacts a Valve {1225}
C175 Generator Sets Electronic Modular Control Panel 3 (EMCP 3)
C175 Generator Sets Engine Operation
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Vibration Damper
3000 Frame SR5 Electric Power Generation Terminal Box - Remove and Install
3500 Generator Sets Zinc Rods - Inspect/Replace
Information for the New Flame Detection Temperature Sensors{108B, 108E, 108M} Information for the New Flame Detection Temperature Sensors{108B, 108E, 108M}
G3516 Petroleum Engines Throttle Control Valve - Install
C15 Petroleum Engines Timing - Calibrate
G3516 Petroleum Engines Throttle Control Valve - Remove
C18 Fire Pump Industrial Engine Heat Exchanger - Disassemble
TH48-E70 Petroleum Transmission and TH48-E70-C27I, TH48-E70-C32I and TH48-E70-C32P Petroleum Power Train Packages Speed Sensor (Transmission) - Engine Output
3512, 3508 and 3516 Generator Sets Safety Messages
3500 Generator Sets Safety Messages
120K Motor Grader Backup Alarm
C18 Fire Pump Industrial Engine Heat Exchanger - Assemble
2008/12/22 A New Turbocharger Cartridge is Used {1052, 1053}
120K Motor Grader Hydraulic System Oil Level - Check
2008/11/17 A New Outer Valve Spring Is Now Used {1100, 1108}
2008/12/08 A New Outer Valve Spring is Now Used {1100, 1108}
2008/11/01 A New Outer Valve Spring Is Now Used {1100, 1108}
R250 Automatic Voltage Regulator Constant Volts Per Hertz Operation - Using Knee Frequency Control
C18 Fire Pump Industrial Engine Jacket Water Heater - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions General Hazard Information