Heat Exchanger - Assemble
Assembly Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the components, if necessary.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install spring pin (7) into heat exchanger (6) .
Show/hide table
Illustration 1 | g01698793 |
Typical Example |
- Position the gasket (not shown) and install core assembly (8) into heat exchanger (6) .
- Install both zinc rods (5) into bonnet (2) .
Show/hide table
Illustration 2 | g01698654 |
- Position the gasket (not shown) and install bonnet (2) onto the heat exchanger.
Show/hide table
Illustration 3 | g01698555 |
- Install bolts (1).
- Position elbow (4) and install bolts (3) .
- Position seal (11) into heat exchanger (6) .
Show/hide table
Illustration 4 | g01698775 |
- Four shims (12) are needed for each bolt (9). Position shims (12) and position bonnet (10) .
- Install bolts (9) .
- Install elbow (13) .
End By: Install the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Install".
Caterpillar Information System:
120K Motor Grader Backup Alarm
3500 Generator Sets Safety Messages
3512, 3508 and 3516 Generator Sets Safety Messages
3612 and 3616 Engines Piston and Rings - Three Ring Piston
2008/10/27 Replace the Two-Piece Piston if the Piston Contacts a Valve {1225}
C175 Generator Sets Electronic Modular Control Panel 3 (EMCP 3)
C175 Generator Sets Engine Operation
3500B Engines and 776D, 777D, 784C, 785C, 789C, 793C and 793D Off-Highway Truck/Tractors Vibration Damper
3000 Frame SR5 Electric Power Generation Terminal Box - Remove and Install
3500 Generator Sets Zinc Rods - Inspect/Replace
Information for the New Flame Detection Temperature Sensors{108B, 108E, 108M} Information for the New Flame Detection Temperature Sensors{108B, 108E, 108M}
G3516 Petroleum Engines Throttle Control Valve - Install
2008/12/22 A New Turbocharger Cartridge is Used {1052, 1053}
120K Motor Grader Hydraulic System Oil Level - Check
2008/11/17 A New Outer Valve Spring Is Now Used {1100, 1108}
2008/12/08 A New Outer Valve Spring is Now Used {1100, 1108}
2008/11/01 A New Outer Valve Spring Is Now Used {1100, 1108}
R250 Automatic Voltage Regulator Constant Volts Per Hertz Operation - Using Knee Frequency Control
C18 Fire Pump Industrial Engine Jacket Water Heater - Remove and Install
TH55FT-E70 and TH55FT-E90 Transmissions General Hazard Information
Installation Procedure for the Space Heater On Generator Sets{4450} Installation Procedure for the Space Heater On Generator Sets{4450}
3512B HD SR500 Generator Sets Configuration Parameters
Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940} Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940}
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove