Radiator and Hydraulic Oil Cooler - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 140-7742     | 套筒     | 2     |
B     | 189-0408     | 钩环组件     | 2     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
Show/hide table
热的冷却液、蒸汽和碱会造成人身伤害。 在工作温度下,发动机冷却液是热的而且处在压力下。 散热器和所有到加热器的管路或发动机中都有热的冷却液或蒸汽。 与它们的任何接触都会造成严重烫伤。 只有当发动机停机且冷却系统压力盖已经冷却到可以徒手触摸时,再慢慢拆下冷却系统压力盖以释放压力。 不要试图在冷却液还热的时候去拧紧软管接头,软管会脱落而造成灼伤。 警告:冷却系统的冷却液添加剂含碱。 应避免它与皮肤和眼睛接触。 |
- 拆下护罩 (1) 和 (2) 。
Show/hide table
图 1 | g01707754 |
- 把冷却液排放到适当的容器中。 请参阅操作和保养手册, "冷却系统冷却液(ELC)- 更换"。
- 将液压油排入合适的容器中。 请参阅操作和保养手册, "液压系统机油 – 更换"。
- 打开机器左侧检修门。 拆下螺栓 (3) 。 打开检修门 (4) 。 固定检修门 (4) 。
Show/hide table
图 2 | g01707756 |
- 将合适的起吊设备连接到发动机罩组件 (5) 上。 发动机罩组件 (5) 的重量约为 68 kg (150 lb)。
Show/hide table
图 3 | g01707758 |
- 拆下螺栓 (6) 。 拆下发动机罩组件 (5) 。
- 拆下支承 (10) 。 从散热器上断开软管 (8) 和 (9) 。 从护罩 (11) 上断开软管 (9) 。 拆卸管 (7) 和 (12) 。
Show/hide table
图 4 | g01707354 |
- 将管 (13) 和 (14) 作为一个整体一起拆下。
Show/hide table
图 5 | g01707355 |
- 从风扇马达上断开软管组件 (15) 。
Show/hide table
图 6 | g01707357 |
- 从支承 (16) 上断开支架 (17) 。
Show/hide table
图 7 | g01707676 |
- 断开软管 (18) 。
Show/hide table
图 8 | g01707759 |
- 断开管 (19) 。
Show/hide table
图 9 | g01707760 |
- 从支承 (16) 上断开支架 (20) 。 重新定位并固定支架 (20) 。
Show/hide table
图 10 | g01707678 |
- 对于另一侧,重复步骤13。
- 断开管组件 (22) 。 断开线束组件 (23) 。 拆下支架和乙醚起动阀 (21) 。 断开软管组件 (25) 。 从支承 (24) 上断开软管组件 (25) 。 重新将软管组件 (25) 定位。
Show/hide table
图 11 | g01707793 |
- 拆下面板 (26) 。
Show/hide table
图 12 | g01707794 |
- 将工具 (A) 、工具 (B) 和适当的起吊设备固定到散热器和液压油冷却器组件 (27) 上。 散热器和液压油冷却器组件 (27) 的重量约为 544 kg (1200 lb)。
Show/hide table
图 13 | g01707795 |
- 拆下螺栓 (28) 。 拆下散热器和液压油冷却器组件 (27) 。
Show/hide table
图 14 | g01707796 |
Caterpillar Information System:
Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940} Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940}
3512B HD SR500 Generator Sets Configuration Parameters
Installation Procedure for the Space Heater On Generator Sets{4450} Installation Procedure for the Space Heater On Generator Sets{4450}
TH55FT-E70 and TH55FT-E90 Transmissions General Hazard Information
C18 Fire Pump Industrial Engine Jacket Water Heater - Remove and Install
R250 Automatic Voltage Regulator Constant Volts Per Hertz Operation - Using Knee Frequency Control
2008/11/01 A New Outer Valve Spring Is Now Used {1100, 1108}
2008/12/08 A New Outer Valve Spring is Now Used {1100, 1108}
2008/11/17 A New Outer Valve Spring Is Now Used {1100, 1108}
120K Motor Grader Hydraulic System Oil Level - Check
2008/12/22 A New Turbocharger Cartridge is Used {1052, 1053}
C18 Fire Pump Industrial Engine Heat Exchanger - Assemble
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Install
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
TH55FT-E70 and TH55FT-E90 Transmissions Transmission Warm-up
345D and 349D Excavators C13 Engine Supplement Fan - Install
2008/11/10 New Starter Lines Group and Prelube Pump Group Are Used {1319, 1451}
345D and 349D Excavators C13 Engine Supplement Fan Drive - Remove
345D and 349D Excavators C13 Engine Supplement Fan Drive - Install
TH48-E80 Petroleum Transmission Oil Filter (Transmission)
C18 Fire Pump Industrial Engine Cylinder Head - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Install
2009/01/26 Troubleshooting the Wastegate Canister {1052, 1057}