Fan - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 140-7742     | 套筒     | 1     |
- 将工具 (A) 和合适的起吊设备连接到十字轴组件 (20) 。 十字轴组件 (20) 的重量大约为 45 kg (100 lb).
Show/hide table
图 1 | g01708339 |
- 将十字轴组件 (20) 放置到位,然后安装螺栓 (21) 。
- 安装罩 (19) 。
Show/hide table
图 2 | g01708338 |
- 将工具 (A) 和适当的起吊设备固定到风扇组件 (10) 上。 风扇组件 (10) 的重量约为 159 kg (350 lb)。 定位风扇组件 (10) 。
Show/hide table
图 3 | g01708335 |
Show/hide table
图 4 | g01708336 |
- 安装螺栓 (18) 。 对另一侧重复此操作。
- 安装螺栓 (17) ,固定风扇组件 (10) 。
Show/hide table
图 5 | g01708334 |
- 安装支架 (16) 。 对另一侧重复此操作。
Show/hide table
图 6 | g01708331 |
- 安装支架 (15) 。
Show/hide table
图 7 | g01708329 |
- 连接软管组件 (14) 。 安装罩盖 (13) 。
Show/hide table
图 8 | g01708327 |
- 将管 (12) 作为一个整体安装。
Show/hide table
图 9 | g01708324 |
- 安装管 (6) 和 (11) 。 连接软管 (7) 和 (8) 。 将软管 (8) 固定到风扇组件 (10) 上。 安装支承 (9) 。
Show/hide table
图 10 | g01708320 |
- 将合适的起吊设备连接到发动机罩组件 (4) 上。 发动机罩组件 (4) 的重量约为 68 kg (150 lb)。 定位发动机罩组件 (4) 并安装螺栓 (5) 。
Show/hide table
图 11 | g01708317 |
- 关闭检修门 (3) 。 安装螺栓 (2) 。 关闭位于左侧的前检测门。
Show/hide table
图 12 | g01708316 |
- 安装防护罩 (1) 。
Show/hide table
图 13 | g01708314 |
- 加注液压系统。 请参阅操作和保养手册, "加注 - 容量"。
- 加注发动机冷却系统。 请参阅操作和保养手册, "冷却系统冷却(ELC)- 更换"。
Caterpillar Information System:
TH55FT-E70 and TH55FT-E90 Transmissions Transmission Warm-up
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Install
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove
Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940} Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940}
3512B HD SR500 Generator Sets Configuration Parameters
Installation Procedure for the Space Heater On Generator Sets{4450} Installation Procedure for the Space Heater On Generator Sets{4450}
TH55FT-E70 and TH55FT-E90 Transmissions General Hazard Information
C18 Fire Pump Industrial Engine Jacket Water Heater - Remove and Install
R250 Automatic Voltage Regulator Constant Volts Per Hertz Operation - Using Knee Frequency Control
2008/11/01 A New Outer Valve Spring Is Now Used {1100, 1108}
2008/12/08 A New Outer Valve Spring is Now Used {1100, 1108}
2008/11/10 New Starter Lines Group and Prelube Pump Group Are Used {1319, 1451}
345D and 349D Excavators C13 Engine Supplement Fan Drive - Remove
345D and 349D Excavators C13 Engine Supplement Fan Drive - Install
TH48-E80 Petroleum Transmission Oil Filter (Transmission)
C18 Fire Pump Industrial Engine Cylinder Head - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Remove
345D and 349D Excavators C13 Engine Supplement Engine - Install
2009/01/26 Troubleshooting the Wastegate Canister {1052, 1057}
2008/12/22 Troubleshooting the Wastegate Canister {1052, 1057}
C18 Fire Pump Industrial Engine Cylinder Head - Install
C18 Fire Pump Industrial Engine Aftercooler - Remove
2008/11/17 Governor Linkage {1151, 1162, 1206, 1264, 1272, 1908}