Engine - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
B     | 140-7742     | 套筒     | 1     |
C     | 1U-9200     | 操纵杆滚轮起重机     | 1     |
- 在将发动机安装到底盘中之前,拆下发动机机油盘。 这很有必要的,使得有足够的空间安装发动机。
- 将适当的起吊设备连接到发动机 (57) 。 发动机 (57) 的重量约为 1270 kg (2800 lb)。 将发动机 (57) 安装入位。
Show/hide table
图 1 | g01713802 |
- 将发动机连接到主泵接头上。
- 使用工具 (C) 和适当的支座,以此支撑主液压泵 (55) 。 主液压泵 (55) 的重量约为 318 kg (700 lb)。 定位主液压泵 (55) 并安装螺栓 (56) 。
Show/hide table
图 2 | g01713798 |
Show/hide table
图 3 | g01713800 |
- 拆下工具 (C) 和相应的支座。
- 安装支承 (59) 。 安装螺栓 (58) 和 (60) 。 拧紧螺栓 (58) 和 (60) 至扭矩为900 ± 100 N·m (664 ± 74 lb ft)。
Show/hide table
图 4 | g01713804 |
Show/hide table
图 5 | g01713803 |
- 连接支架 (54) 。
Show/hide table
图 6 | g01713795 |
- 连接电缆组件 (52) 。 拧紧电缆组件 (52) 至扭矩为 31 ± 4 N·m (22 ± 3 lb ft)。 连接卡箍 (53) 。
Show/hide table
图 7 | g01713794 |
- 将线束组件 (49) 连接到支架 (50) 上。 连接线束组件 (49) 。 连接接地束带 (51) 。
Show/hide table
图 8 | g01713793 |
- 连接线束组件 (46) 。 连接夹子 (47) 。 连接线束组件 (48) 、
Show/hide table
图 9 | g01713787 |
- 连接软管 (45) 。 将阀 (44) 转到打开位置。
Show/hide table
图 10 | g01713786 |
- 连接软管组件 (43) 。
Show/hide table
图 11 | g01713785 |
- 连接软管组件 (42) 。
Show/hide table
图 12 | g01713779 |
- 安装盖 (41) 。
Show/hide table
图 13 | g01713713 |
- 安装油滤清器和底座 (40) 。 连接支架 (39) 。
Show/hide table
图 14 | g01713585 |
- 连接软管组件 (38) 。
Show/hide table
图 15 | g01713584 |
- 连接软管组件 (37) 。
Show/hide table
图 16 | g01713582 |
- 安装盖 (36) 。 将线束组件 (35) 连接到盖 (36) 上。
Show/hide table
图 17 | g01710964 |
- 安装护罩 (34) 。
Show/hide table
图 18 | g01710961 |
- 将工具 (B) 和适当的起吊设备连接到支承 (33) 上。 支承 (33) 的重量约为 43 kg (95 lb)。 安装支承 (33) 。
Show/hide table
图 19 | g01710960 |
- 将盖 (32) 作为一个整体进行安装。
Show/hide table
图 20 | g01710959 |
- 安装支架 (30) 和盖 (31) 。
Show/hide table
图 21 | g01710956 |
- 安装支承 (29) 。
Show/hide table
图 22 | g01710955 |
- 安装软管 (28) 。
Show/hide table
图 23 | g01710954 |
- 连接乙醚起动辅助管 (27) 。
Show/hide table
图 24 | g01710953 |
- 连接软管 (24) 。 连接夹子 (25) 。
Show/hide table
图 25 | g01710952 |
- 连接线束组件 (21) 。 连接电缆组件 (20) 和 (22) 。 拧紧电缆组件 (22) 至扭矩为 18 ± 2 N·m (160 ± 18 lb in)。 拧紧线束组件 (20) 至扭矩为 4 ± 1 N·m (35 ± 2 lb in)。 连接夹子 (23) 。
Show/hide table
图 26 | g01710949 |
- 连接线束组件 (19) 。 定位制冷剂压缩机 (16) 。 安装螺栓 (17) 。 逆时针转动皮带张紧器,以便安装皮带 (18) 。 安装皮带 (18) 。
Show/hide table
图 27 | g01710948 |
- 连接软管组件 (15) 。
Show/hide table
图 28 | g01710947 |
- 定位盖 (11) 。 定位支承 (13) 。 安装螺栓 (14) 。 降低盖 (11) 。 安装螺栓 (12) 。
Show/hide table
图 29 | g01710945 |
Show/hide table
图 30 | g01710943 |
- 安装支架 (10) 。
Show/hide table
图 31 | g01710938 |
- 安装护罩 (9) 。
Show/hide table
图 32 | g01710934 |
- 安装盖 (7) 。 拧紧支架 (8) 。 连接管 (6) 并连接到盖 (7) 上。
Show/hide table
图 33 | g01710931 |
- 安装盖 (4) 。 安装管 (5) 。 定位软管 (3) 。 连接软管 (3) 。
Show/hide table
图 34 | g01710929 |
- 将工具 (A) 和适当的起吊设备连接在支承 (1) 上。 支承 (1) 的重量约为 34 kg (75 lb)。 安装支架 (1) 。 安装支架 (2) 。
Show/hide table
图 35 | g01710928 |
- 将燃油切断阀拨到 接通位置。 请参阅操作和保养手册, "燃油箱切断和排放控制"。
- 向冷却系统加注冷却液。 请参阅操作和保养手册, "冷却系统冷却(ELC)- 更换"。
End By:
- 安装机油盘。 请参阅 拆解和组装, "机油盘 - 安装"。
- 安装消音器。 请参阅 拆解和组装, "消音器 - 安装"。
- 安装发动机罩。 请参阅 拆解和组装, "发动机罩 - 安装"。
Caterpillar Information System:
345D and 349D Excavators C13 Engine Supplement Engine - Remove
C18 Fire Pump Industrial Engine Cylinder Head - Remove
TH48-E80 Petroleum Transmission Oil Filter (Transmission)
345D and 349D Excavators C13 Engine Supplement Fan Drive - Install
345D and 349D Excavators C13 Engine Supplement Fan Drive - Remove
2008/11/10 New Starter Lines Group and Prelube Pump Group Are Used {1319, 1451}
345D and 349D Excavators C13 Engine Supplement Fan - Install
TH55FT-E70 and TH55FT-E90 Transmissions Transmission Warm-up
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Install
345D and 349D Excavators C13 Engine Supplement Radiator and Hydraulic Oil Cooler - Remove
Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940} Installation and Adjustment Procedure for the 332-8662 Actuator Kit (Wastegate){1052, 1053, 1057, 1940}
2009/01/26 Troubleshooting the Wastegate Canister {1052, 1057}
2008/12/22 Troubleshooting the Wastegate Canister {1052, 1057}
C18 Fire Pump Industrial Engine Cylinder Head - Install
C18 Fire Pump Industrial Engine Aftercooler - Remove
2008/11/17 Governor Linkage {1151, 1162, 1206, 1264, 1272, 1908}
C18 Fire Pump Industrial Engine Aftercooler - Install
C18 Fire Pump Industrial Engine Aftercooler - Disassemble
TH48-E80 Petroleum Transmission Pressure for Gear Pump (Transmission Charging) - Test and Adjust
C18 Fire Pump Industrial Engine Aftercooler - Assemble
The Incorrect Fuel Enable Valve May Cause a Problem With the Aftertreatment Regeneration Device{1262, 1723} The Incorrect Fuel Enable Valve May Cause a Problem With the Aftertreatment Regeneration Device{1262, 1723}
C15 Petroleum Engines Oil Temperature Is High
C13 On-highway Engine Alternator Mounting